Linotronic 530
Boot Status Messages
Code: Description:
| INIT RECORDER START | Recorder initialization started | |
| INIT RECORDER 0 | Time loop of about 45s. (LES power on delay) | |
| INIT RECORDER 1 | Polygon drive initialized using the last X resolution setting | |
| INIT RECORDER 2 | Film feed initialized using the last Y resolution value | |
| INIT RECORDER 3 | Current density set | |
| INIT RECORDER 4 | Cutter initialization, move to cutter stop, if necessary | |
| INIT RECORDER DONE Recorder is ready |
Recorder initialization completed successfully (In Test mode, not all initialization routines are executed; certain errors may not be recognized) |
Status Messages During Operation
Message: Description:
| LI5 ENABLE | LI5 interface enabled; parameters can be defined also from the LT55 panel (equal priority) |
|
| PROCESS ACTIVE | A process is active; no other process can be started. The process may be aborted by (SHIFT) STOP |
|
| USER STOPPED | Process aborted by the user | |
| FILM ADVANCING | Film is being advanced | |
| FILM ADVANCE DONE | Film advance completed | |
| FILM CUTTING | Film is being cut | |
| FILM CUT DONE | Film cutting completed | |
| INSERT FILM | Insert film into the film transport system. Wait until the message is displayed |
|
| ADJUST FILM | Adjust the film. Unlock the film drive (right-hand red button) Centre the film. Lock the film drive |
|
| FILM LOADING | Film is being loaded into the film transport system | |
| CONTINUE FILM LOAD | Film loading is continued. Film advance with film cut | |
| FILM LOAD DONE | Film loading completed. Insert take-up cassette | |
| ALREADY FILM | Film already loaded | |
| ABORT FILM LOAD | Film loading aborted. Photomaterial was not recognized | |
| FILM UNLOADING | Film unloading is started | |
| FILM UNLOAD DONE | Film unloaded from the film transport system | |
| CUT BEFORE UNLOAD | Film loading aborted. Cut material | |
| NO FILM SUPPLY | No film available in film transport system (end of film) | |
| WARNING END OF FILM | End of film approaching alert | |
| FILMLOAD > CMD- ERROR |
Photomaterial error. (Try REC 1) | |
| IMAGING | Output in progress | |
| IMAGING DONE | Output completed | |
| IMAGING DONE | Recorder test printout in progress | |
| TEST IMAGING DONE | Recorder test printout completed | |
| DENSITY JOB STARTED | Density test printout in progress (several densities) | |
| DENSITY JOB DONE | Density test printout completed | |
| ACTUAL JDNS STARTED |
Density test printout in progress (current density only) | |
| ACTUAL JDNS STARTED |
Density test printout completed | |
| CHANGE TAKEUP CASS | Change the take-up cassette | |
| NO TAKEUP CASSETTE | Take-up cassette not inserted | |
| TAKEUP CASS FULL | Take-up cassette is full; material is cut automatically | |
| REMOVE TAKEUP CASS |
Remove the take-up cassette – cut has been performed | |
| CHECK CUTTER POS | Cutter not at stop position. Do not close the film transport system to avoid damaging the cutter |
|
| WARNING DENSITY | The selected density is too low. SOL detection may not be possible |
|
| TAKO ACTIVE | Calculation of tacho correction | |
| WARNING TAKO | Polygon tacho correction not successful | |
| WARNING FILM DRIVE | Zero mark of the film transport roller not found | |
| RANGE OVERFLOW | Zero mark of the film transport roller not found | |
| X.LM + X.M > F.WIDTH | Left margin plus measure greater than film width | |
| NO VALID RESOLUTION | The defined resolution is not supported | |
| NO RES FOR LI2 STNG | The defined resolution is not allowed with the current LI2 Parameters. Select 16 MHz async mode in the INTERFACE menu; the RIP must also support the 16 MHz mode |
|
| OLP FORCED CUT | Forced cut of material is being executed because the maximum galley length of the online processor is reached |
|
| OLP AUTOMATIC CUT | Auto film cut for online processor is being executed |
Status Error Messages
Message: Description:
| RIP, NOT CONNECTED | A backend defined as imagesetter cannot see the RIP | |
| RIP > NOT SELECTED | RIP and recorder not synchronized | |
| RECORDER > TIME OUT | START signal did not trigger an interrupt. No light at SOL? | |
| RECORDER > TIME OUT | SOL missing. SOL-threshold, but no SOL recognized. Light intensity too low? SOL amplifier failure |
|
| NO LIGHT > DENSITY | Selected density too low. SOL is not recognized. Increase the density | |
| SPINNER > TIME OUT | Selected density too low. SOL is not recognized. Increase the | |
| DENSITY >TIME OUT | At present not used | |
| ERROR TAKO > WRITE | Tachometer correction error on writing the correction values. Has been Polygon fault |
|
| ERROR TAKO >READ | Tacho correction error on reading the correction values | |
| TAKO ACTIVE | Tachometer correction iteration. Please wait | |
| ERROR > CUT [120] | Cutter not at stop position. Limit switch still active | |
| ERROR > CUT [121] | Cutter time-out. Cutter blocked | |
| ERROR > CUT [122] | Film advance in progress. Cutting not allowed | |
| ERROR > FILM LOAD | Film loading error | |
| OLP NOT OPERABLE | Online processor not available. Check connection | |
| OLP NOT READY | Online processor not ready. Check online processor | |
| OLP BRIDGE | Failure of bridge to online processor | |
| LI2 >SENDER NOT OPR | LI2 sender not operable. SOPR deactivated | |
| LI2 >SCAN OVERRUN | Too many pixels in transferred scan line | |
| LI2 >SENDER ERROR | Recorder aborted the job at the receiver operable signal (ROPR). A new output request is issued but the old sender page signal (SPGE) of the sender is still active |
|
| LI2 >TIME OUT | Abort of an LI2 connection to the recorder by time-out. This error may, at present, not occur because a time-out is not defined |
|
| LI2 WITHOUT LI5 | Output is not controlled via the LI5 interface. Output is started by pressing the START key |
|
| LI5 >NO PARTNER | LI5 partner (RIP) not available | |
| LI5 >TIME OUT | Time-out on the LI5 interface. This error may at present not occur because a time-out is not defined |
|
| LI5 >OVERRUN | DUART overrun on the LI5 interface. LI5 interface may not be served by the recorder | |
| LI5 >PARITY ERR | Parity error on the LI5 interface | |
| LI5 >FRAMING ERR | Framing error on the LI5 interface | |
| LI5 >SYNCHR ERR | Software synchronization error on the LI5 interface | |
| HARD-REV TOO LARGE | Hardware revision number too large for firmware | |
| HARD-REV TOO SMALL | Hardware revision number too small for firmware | |
| HARD-REV TOO SMALL | Wrong flag returned by application process | |
| PLEASE RESET | Press both Reset keys |
EEPROM Errors
Message: Description:
| EEPROM >INIT | EEPROM initialization. Default values are assumed | |
| EEPROM >INIT | EEPROM update. After installation of a new program on the REC1 board the EEPROM data has been defaulted |
|
| EEPROM >NEW INIT | A new EEPROM was installed. Default values assumed | |
| EEPROM ERROR | General EEPROM error | |
| EEPROM >CHECKSUM | Wrong checksum of EEPROM data | |
| EEPROM OVERFLOW | EEPROM full. (All three EEPROM blocks were used and may no longer be written) Install new EEPROM |
|
| EEPROM >OLDSOFTWARE | Firmware older than EEPROM data structure. Install new firmware | |
| EEPROM >OLD EEPROM | EEPROM data structure obsolete. The firmware automatically converts the data structure. Check the data |
|
| EEPROM>TOO OLD | EEPROM structure very obsolete. The firmware automatically converts the data structure. Check the data |
|
| EEPROM>TOO OLD | EEPROM defect. Replace the EEPROM |
NVRAM Errors
Message: Description:
| NVRAM >TOO OLD | NVRAM data structure obsolete. Reinitialze the LT55 | |
| NVRAM >OLDSOFTWARE | Firmware older than NVRAM data . Install new firmware | |
| NVRAM >FATALERROR | Fatal NVRAM error; initialize the LT55 panel | |
| NVRAM >ERROR | General NVRAM error, initialize LT55 | |
| NVRAM >MESSAGE ERR | General NVRAM error, initialize LT55 |
