Computer to Plate | RS Prepress Services

Heidelberg ProSetter

Error: Description: More Details:

0	Recorder is ready for operating
1	Internal Error	An error occurred in the program sequence
2	Internal Error	An error occurred in the program sequence
12	Internal Error	Internal communication error
35	An error occurred in a database.	The specified record is not available.
36	An error occurred in a database.	The specified error got a different type.
37	An error occurred in a database.	The length of the value of the specified error is to long for the delivered buffer
38	An error occurred in a database.	The length of the buffer of the specified record is to short for the delivered value
40	An error occurred in a database	The insertion of a record into a database is not possible
41	An error occurred in the file system	A file could not be opened
42	An error occurred in the file system	A file could not be closed
43	An error occurred in the file system	A file could not be seeked
44	An error occurred in the file system	A file could not be written
45	An error occurred in the file system	A file could not be read
48	An error occurred while allocating memory	Memory could not be allocated
49	An error occurred while parsing a source	A syntax error is occurred
94	Internal system error	Error using operating system function
95	Internal system error	Error using operating system function
96	Internal system error	Error using operating system function
97	Internal system error	Error using operating system function
98	Internal system error	Error using operating system function
99	Internal system error	Error in file operation
100	Internal system error	Error in file operation
101	Internal system error	Error in file operation
102	Internal system error	Error in file operation
103	Internal system error	Error in file operation
104	Internal system error	Error in file operation
105	Internal system error	Error in file operation
106	Internal system error	Error in file operation
107	Internal system error	Error in file operation
108	Internal system error	Error in file operation
109	Internal system error	Error in file operation
110	Internal system error	Error in file operation
111	Internal system error	Error in file operation
112	Internal system error	Error using operating system function
113	Internal system error	Error using operating system function
114	Internal system error	Error using operating system function
115	Internal system error	Error using operating system function
116	Internal system error	Error using operating system function
117	Internal system error	Error using operating system function
118	Internal system error	Error using operating system function
119	Internal system error	Error using operating system function
120	Internal system error	Error using operating system function
121	Internal system error	Error using operating system function
122	Internal system error	Error using operating system function
123	Internal system error	Error using operating system function
124	Internal system error	Error using operating system function
126	Internal system error	Error in file operation
128	Internal system error	Error in file operation
129	Internal system error	Error in filebox
130	Internal system error	Error in filebox
133	Communication error	Speedway communication error
134	Communication error	Speedway communication error
135	Internal system error	Error using operating system function
136	Internal system error	Error using operating system function
146	Internal system error	Internal communication error
147	Internal system error	Internal communication error
148	Internal system error	Internal communication error
149	Internal system error	Internal communication error
150	Internal system error	Internal communication error
151	Internal system error	Internal communication error
152	Internal system error	Internal communication error
153	Internal system error	Internal communication error
154	Internal system error	Internal communication error
155	Internal system error	Error using operating system function
156	Internal system error	Error using operating system function
157	Internal system error	Error using operating system function
158	An error occurred in a database	The erasing of a record out of a database is not possible
163	Internal system error	Error in file operation
164	Internal system error	Error in file operation
170	An internal hardware error occurred	FPGA busy error
171	An internal hardware error occurred	FPGA detection error
172	An internal hardware error occurred	FPGA initialization error
173	An internal hardware error occurred	FPGA busy error
174	An internal hardware error occurred	FPGA frame data error during configuration
175	An internal hardware error occurred	FPGA length count error
220	An error occurred in a database	A file which should be copied does not exist
221	An error occurred in a database	A file could not be deleted
222	An error occurred in a database	A file could not be copied
223	An error occurred in a database	A directory could not be created
224	An error occurred while parsing a source	A serious syntax error is occurred
225	An error occurred while parsing a source	A serious syntax error is occurred
234	Internal error	Operating system error
235	Internal error	Operating system error
237	An internal hardware error occurred	Communication error on the SPI Bus
282	Internal system error	Error in Package
283	Internal system error	Error in Package
284	Internal system error	Error in FPGA box
285	Internal system error	Error in FPGA box
293	The current machine type is usable for test purposes only	The current machine type is usable for test purposes only
294	The current machine type is invalid	The current machine type is invalid
295	The current machine variation is invalid	The current machine variation is invalid
313	Internal system error	Operating system error
314	Internal error	Operating system error
319	An error occurred while parsing a source	A semantics error occurred
320	An error occurred while parsing a source	Simple semantics error
321	An error occurred while parsing a source	Serious semantics error
322	Switch off sequence initiated	Fast switch off sequence initiated
323	Fast switch off sequence initiated	A second switch off command was received. Only data will be saved before switch
324	An error occurred in the parameter database	The parameter configuration file does not exist
400	Internal error	Undefined error
401	Internal error	Undefined error
402	Internal error	Wrong magic number received with the data
403	Internal error	Buffer size error
404	Internal error	Checksum error
405	Internal error	Error after select() function
406	Internal error	select() timeout
407	Internal error	Error after ioctl() function
408	Internal error	Not enough buffer for download
409	Internal error	Not enough buffer for download
410	Internal error	Not enough FLASH memory
411	Internal error	Unknown FLASH vendor
412	Internal error	Unknown FLASH module
413	Internal error	Invalid FLASH map
414	Internal error	FLASH not ready
415	Internal error	Error clearing the FLASH
416	Internal error	Error clearing the FLASH
417	Internal error	Error clearing the FLASH
418	Internal error	Error clearing a FLASH sector
419	Internal error	Error clearing a FLASH sector
420	Internal error	Error checking a FLASH sector
421	Internal error	Timeout programming the FLASH
422	Internal error	FLASH not ready
423	Internal error	Error comparing the FLASH after write operation
424	Internal error	Error connecting with an interrupt
425	Internal error	Error activating an interrupt
426	Internal error	Out of init error memory
427	Internal error	Error initializing the hardware
428	Internal error	Error reading from FLASH
429	Internal error	Error writing to FLASH
430	Internal error	Error after open() function
431	Internal error	Error after close() function
440	Internal system error	Error using operating system function
441	Internal system error	Error using operating system function
442	Internal system error	Error using operating system function
443	Internal system error	Error using operating system function
3001	The ventilator for the central electronics is defective! Forcing power off of the recorder	Electronics ventilator monitor reports an error. You cannot continue operation. Powering down the recorder
3002	Wrong Bacher punch configuration	Bacher Configuration parameter (PID 21958) is wrong. The bit map of the Bacher Configuration (PID 21958) must be a subset of the bit map of the Punch Configuration (PID 766)
3003	The ventilator of the air filter is not working. There will be a loss of recorder quality due to dirty mirrors if this error occurs over a longer period of time	The ventilator of the air filter is not rotating or the phase sequence sensor is defective
3004	The air filter is used and must be replaced. There will be a loss of recorder quality due to dirty mirrors if this error occurs over a longer period of time	The sensor for the air filter reports that the filter is used
3005	Max. output level of the optical head is not enough to image in the selected mode	Max. output level of the optical head is not enough to image in the selected mode
3006	Max. output level of the optical head is not enough to image in the selected mode	Cannot end an action in the recorder because of a preceding error or power-off function
3007	Punch setting doesn’t match punch configuration	RIP punch action doesn’t match punch configuration
3008	ATTENTION: Plate lost in device! Do NOT correct error	A plate was probably lost in the device during initialization. Error correction is illegal in this present state
3009	Internal communication error	Communication with an internal assembly (e.g. Optic) failed
3010	Internal communication error	Communication with with the Autoloader failed
3011	Error in the slow scan unit	Could not find resolution for calculation of an imaging ramp
3012	Network addresses (IP addresses) conflict	The two network addresses of the recorder must not come from the same network
3014	An error occurred in the mirror motor unit	The time monitor reports timeout during the spin-up phase of the mirror motor
3015	An error occurred in the mirror motor unit	The time monitor reports timeout during the spin-down phase of the mirror motor
3016	An error occurred in the air supply unit	The air safety switch is not closed
3017	An error occurred in the air supply unit	The mirror air cooler temperature is to high
3018	An error occurred in the air supply unit	Communication error on the I2C-Bus
3019	Internal communication error	The air pump did not start
3020	An error occurred in the air supply unit	The focus stepping motor cannot find the zero position
3021	An error occurred in the optic unit	The focus stepping motor cannot find the zero position
3022	A parameter set-up error occurred in the optic unit	The focus position set point is not within the permissible range
3023	An error occurred in the optic unit	The filter stepping motor cannot find the zero position
3024	An error occurred in the optic unit	The filter stepping motor cannot leave the zero position
3025	A parameter set-up error occurred in the optic unit	The filter number is not within the permissible range
3026	A parameter set-up error occurred in the optic unit	The number of the shaping element is not within the permissible range
3027	An error occurred in the optic unit	The adjust bias current of the laser diode is higher than the maximum current
3028	An error occurred in the optic unit	The maximum bias current of the laser diode is not sufficient to achieve the required light value
3029	An error occurred in the optic unit	The adjusted current of the laser diode is higher than the maximum current
3030	A parameter set-up error occurred in the optic unit	The modulation current of the laser diode set to maximum is not sufficient to achieve the required light value
3031	An error occurred in the optic unit	The laser diode must be on for the light stabilization
3032	An error occurred in the optic unit	The light stabilization must be off
3033	An error occurred in the optic unit	Passed value is to high for this function
3034	An error occurred in the optic unit	Passed value is to low for this function
3050	On board device error	Unable to set mirror power supply (36 V)
3051	An error occurred in the slow scan unit	The stepper board signals a short circuit, the safety loop is open or power supply (36V) failed
3052	An error occurred in the slow scan unit	The stepper board signals high temperature
3053	An error occurred in the slow scan unit	The stepper board signals not ready
3054	An error occurred in the slow scan unit	The carrier reaches the left limit
3055	An error occurred in the slow scan unit	The carrier reaches the right limit
3056	An error occurred in the slow scan unit	The carrier is moving when it is not allowed
3057	An error occurred in the slow scan unit	The safety loop is not closed
3058	An error occurred in the slow scan unit	An interrupt has occurred when not expected. Interrupt: Stop
3059	An error occurred in the slow scan unit	An interrupt has occurred when not expected. Interrupt: Signal of light barrier has changed
3060	An error occurred in the slow scan unit	An interrupt has occurred when not expected. Interrupt: Destination reached
3061	An error occurred in the slow scan unit	A SlowScan timeout is occurred during finding a position or moving into the light barrier
3062	An error occurred in the slow scan unit	A valid ramp could not be found
3063	An error occurred in the slow scan unit	A ramp which fits into a specified distance could not be found
3064	A parameter error occurred	The value of a parameter is not valid
3078	An internal software error occurred	An attempt to read an uninitialized ADC device.
3088	An error occurred while material handling	Timeout at build vacuum
3089	An error occurred while material handling	Timeout at vacuum off
3138	An error occurred at punch init	Punch not connected or not configured
3159	An error occurred in the slow scan unit	The safety loop is not closed
3160	An error occurred in the slow scan unit	The carrier reaches the left limit
3161	An error occurred in the slow scan unit	The carrier reaches the right limit
3162	An error occurred in the slow scan unit	The stepper board signals not ready
3165	An error occurred while setting the light intensity	The BaseIntensity value for the selected resolution of the current job is lower than the adjustable light
3168	An error occurred in the slow scan unit	The feed ramp could not be written
3169	An error occurred in the slow scan unit	Error while calculating feed ramp data
3198	Not calibrated resolution selected	The selected resolution is not calibrated. The BaseIntensity parameter for the selected resolution is zero
3199	An communication error to the optic head occurred	The communication to the optic head is broken
3200	An communication error to the optic head occurred	The communication to the optic head is faulty
3201	An error occurred in the optichead unit	The number of gate impulses generated by the Image-Control is out of range
3202	An error occurred in the optichead unit	The temperature of the laser diode did not change after switching on the temperature regulation
3203	An error occurred in the optichead unit	The temperature of the laser diode is over the maximum allowed temperature
3204	An error occurred in the optichead unit	A parameter transmitted to the optichead is out of range
3205	An error occurred in the optichead unit	A parameter transmitted to the optichead is out of range
3206	An error occurred in the optichead unit	An error without a defined event has occurred
3207	An error occurred in the optichead unit	The light value on the laser diode with the bias current alone is higher than the value in the application data. This may be due to an error in the primesetter or a not initialized material data set or an defective optichead
3208	An error occurred in the optichead unit	The error occurs if you switch on the temperature regulation on the optichead without a regulation device
3209	An error occurred in the optichead unit	The mirror phased out during transmission. The mirror is not locked
3211	The mirror phased out during transmission. The mirror is not locked	The detect vacuum is much too low
3212	An error occurred while selecting the focus value	The RIP transmitted resolution is not a element of the recorder resolution table
3213	An error occurred while selecting the focus value	The calculation of the spotshape value failed
3214	An error occurred in the optic unit	The calculation of the filter value failed
3215	An error occurred in the optic unit	The calculation of the physical focus value failed
3216	An error occurred in the optic unit	The calculation of the physical focus value failed
3217	The safety loop was at least briefly interrupted
3226	An error occurred while setting the light intensity	The BaseIntensity value for the selected resolution of the current job is lower than the adjustable light
3227	An error occurred while setting the light intensity	The BaseIntensity value for the selected resolution of the current job is higher than the adjustable light
3228	An error occurred in the optichead unit	The light value on the laser diode with the modulation current alone is to high . This may be due to an error in the primesetter or an defective optichead
3229	An error occurred in the air supply unit	The high-water sensor is still active, after water blow-off
3230	An error occurred in the air supply unit	The high-water sensor is still active, after water blow-off
3238	Plate on table missing for load	Possibly plate detector (on plate table) defect
3239	An error occurred at punch action	Timeout at punch action (10s) at arrive ls
3240	An error occurred at material transport	Timeout at drive plate slider to Down-Wait Position (prepare to load)
3241	An error occurred at material transport	Timeout at drive plate slider to Down-Free position (unload plate)
3242	An error occurred at material transport	Timeout at drive plate slider to Up-Unload Position (unload plate or init)
3243	An error occurred at material transport	Timeout at center plate on table
3244	Plate on the table is not valid. Measured plate width is different to requested plate	Plate on the table is not valid. Measured plate width is different to requested plate
3245	Inserted plate is not valid. Measured plate length is different to requested plate	Inserted plate is not valid. Measured plate length is different to requested plate
3246	Unexpected plate on table detected. Exposed plate can not be ejected	Unexpected plate on table detected. Exposed plate can not be ejected
3247	An error occurred at material transport	A timeout is occurred during moving the lift into a position. No interrupt occurred
3248	There is no plate at the grip. Loading material isn’t possible	The plate sensor at the grip signals no-plate
3249	An internal hardware error occurred	The lift stepping motor cannot find it’s zero position
3250	An internal hardware error occurred. One or more fans at the back-wall don’t work	One or more of the guide fans at the back-wall don’t work
3251	An internal hardware error occurred. One or more fans at the back-wall don’t work	One or more of the guide fans at the back-wall don’t work
3252	An internal hardware error occurred. One or more fans at the back-wall don’t work	One or more of the guide fans at the back-wall don’t work
3253	An internal hardware error occurred. One or more fans at the back-wall don’t work	One or more of the guide fans at the back-wall don’t work
3254	The safety loop is open	The safety loop is open
3255	An internal hardware error occurred	An internal hardware error occurred
3256	An internal hardware error occurred	An internal hardware error occurred
3258	Plate position in lift is not valid for unloading	Inserted plate is not valid. Measured plate length is different to requested plate
3259	An error occurred at material transport	An error occurred at material transport
3260	An error occurred at material transport	Moving the flaps failed. They didn’t reach their in-or-out target position
3261	An error occurred at material transport	Moving the flaps failed. They didn’t reach their in-or-out target position
3262	An error occurred at material transport	Lift didn’t reach it’s set position. Maybe stopped by a sporadic interrupt
3263	An error occurred at material transport	Moving the lift isn’t possible because the flaps stays in the path
3264	An error occurred at material transport	Moving the lift isn’t possible because the grip unit is in horizontal position
3265	An error occurred at material transport	There are no valid parameter available
3266	An error occurred at material transport	Lift lost it’s position. Lower reference light-barrier shows a position error bigger than 1.2mm
3267	Material Length isn’t possible to load	It isn’t possible to move the lift into the calculated load position for this material length
3269	An error occurred at material transport	This operation isn’t possible at this time because the system wasn’t initialized correctly
3270	The set lift position is out of range	It isn’t possible to move the lift into the calculated load position for this material length
3271	An error occurred at material transport	There are no valid parameter available
3272	An error occurred at material transport	Initializing of the lift not possible – maybe the grip is still under the hooks in the indrum
3274	An error occurred in the lift and grip unit	The stepper board signals not ready
3275	An error occurred in the lift and grip unit	The lift ramp could not be written
3276	An error occurred in the lift and grip unit	Error while calculating lift ramp data
3277	An error occurred in the lift and grip unit	Moving the lift isn’t possible because the flaps stays in the path
3278	An error occurred in the lift and grip unit	FPGA and Parameter Grip Mode do not match
3279	part of the covering isn’t closed correctly or the emergency switch is activated
3280	Exposed plate is keeping in recorder	Exposed plate is keeping in recorder
3281	The service switch bypasses the safety loop
3286	Unexpected plate on table detected. Init recorder or error correction not possible	Unexpected plate on table detected. Init recorder or error correction not possible
3287	An error occurred in the lift and grip unit	The lift stepping motor cannot find it’s zero position
3288	An internal hardware error occurred. One or more fans at the plate-table don’t work	One or more of the guide fans at the plate-table don’t work
3289	An internal hardware error occurred. One or more fans at the plate-table don’t work	One or more of the guide fans at the plate-table don’t work
3296	Voltage failure	The negative analog 5 V failed
3297	Voltage failure	The negative analog 5 V failed
3298	Voltage failure	The negative analog 5 V failed
3299	Voltage failure	The positive 36 V failed
3300	Voltage failure	The positive 15 V failed
3301	Voltage failure	The positive 42 V failed
3302	Voltage failure	The positive 7.5 V failed
3303	Voltage failure	The positive 7.5 V failed
3304	Voltage failure	The positive analog 24 V failed
3305	Voltage failure	The positive 3.3 V failed
3306	Voltage failure	The positive 2.5 V failed
3307	The positive 2.5 V failed	Safety loop check failed. Check the Logfile for further information
3309	An error occurred in the material base	The requested material does not exist
3310	An error occurred at material transport	The plate center unit does not left the light barrier
3311	An error occurred at material transport	An unexpected motor stop from stepper counter at plate centering
3312	An error occurred in the air supply unit	The air pressure did not reach the required minimum
3315	The aging of the laser diode has accelerated	Too few exposure time has elapsed since the last automatic increase of the bias current setvalue. Nevertheless the bias current setvalue will be increased
3316	The end of lifetime of the laser diode is approaching	The nominal maximum limit of the total current of the laser diode has been reached
3317	An error occurred in the air supply unit	The mirror air pressure is above stop-limit
3318	An error occurred in the air supply unit	The mirror air pressure is above stop-limit
3325	An error occurred in the material base. The preferred shaft has not been specified	The preferred shaft is used in case a material shall be loaded which gets no link from any shaft
3326	An error occurred in the material base	The name of the material that is send with the command request material is invalid
3327	Remove Plate from table. Plate is exposed	Remove Plate from table
3328	Remove Plate from table. Plate is unexposed	Remove plate from manual tray
3329	OLP program change necessary	OLP program change necessary
3913	Autoloader error state detected	Autoloader error state detected
3914	Internal software or parameter error	Syntax error in debug configuration
3915	The Emergency Switch is activated
3916	The boot sequence failed. Please reboot the system	The boot sequence failed. Please reboot the system
4001	Internal software or parameter error	Syntax error in debug configuration
4002	Execution error – A general STOP occurred	A general BREAK occurred
4003	Internal error – sensor not recognized	A sensor in the device does not respond
4004	Internal error – setting a sensor failed	Writing to a sensor failed
4005	Internal error – actuator not recognized	An actuator in the device does not respond
4006	An actuator in the device does not respond	Writing to an actuator failed
4007	Error checking the Cassette/Waste safety loop	There is a problem with the safety loop of the Cassette / Waste section. Checking it failed
4008	Invalid Autoloader machine type set
4009	Any part of the covering isn’t closed correctly
4010	The safety loop was at least briefly interrupted
4011	The service switch bypasses the safety loop
4012	Internal system error	Error using operating system function
4013	Error checking the cover safety loop	There is a problem with the safety loop of the cover section. Checking it failed
4014	Runtime error	Internal software error
4015	The Emergency Switch is activated
4016	The boot sequence failed. Please reboot the system	The boot sequence failed. Please reboot the system
4100	Error separating a plate
4101	Error initializing the shutter	Unable to access the shutter init sensor
4102	Error initializing the shutter	Unable to quit the shutter init sensor
4103	Error moving the shutter	Unable to move the shutter into waste position
4104	Error moving the shutter	The shutter failed to get to the material transfer position
4105	Error polling a load table plate sensor	Load table plate sensor on the suction cart not found
4106	Error separating	Plate lost while separating or during transport to the entry of the load table plate. The plate did not arrive at the relevant sensor
4107	Error placing the plate on the load table plate	Plate lost during transport to the load table plate, the table plate sensor on the suction cart fails to detect the plate at the end of the transfer process
4108	Error moving the shutter	Separator exit sensor not left when transporting the plate to the load table plate
4109	Paper sheet lost when separating	When depositing the paper sheet, the vacuum shows that the sheet was lost during transfer into the waste container
4110	Error initializing the stripper unit	Stripper unit did not arrive at the init position during initialization
4111	Error initializing the stripper unit	Unable to quit the init sensor of the stripper unit
4112	Error moving the stripper unit into working position	Unable to quit the parking sensor of the stripper unit
4113	Error moving the stripper unit	Unable to get to the parking sensor of the stripper unit
4115	Moving the stripper unit into the parking position caused an error several times	Moving the stripper unit into the parking position caused an error several times
4116	A sensor was not reached while the stripper unit was moving to its park position	The light barrier of the park sensor was not detected while the stripper unit was moving to its park position
4117	A sensor was not reached during initialization of the stripper unit	The light barrier of the park sensor was not detected during initialization of the stripper unit
4118	A sensor was not reached during normalization of the shutter	A sensor was not reached during normalization of the shutter
4119	A sensor was not reached during initialization of the shutter	The zero light barrier was not detected during initialization of the shutter
4120	Error initializing the cassette shutter	Cassette shutter motor did not arrive at the init position during initialization
4121	Error initializing the cassette shutter	Unable to quit the init position when initializing the cassette shutter motor
4122	Error while preparing cassette shade drive for taking a new cassette	Sensor could not detect the requested phase 1 during the specified number of attempts during initialization of the cassette shade drive
4123	Error while preparing cassette shade drive for taking a new cassette	Sensor could not detect the requested phase 2 during the specified number of attempts during initialization of the cassette shade drive
4124	A sensor was not reached during initialization of the cassette shade drive	The light barrier of the close sensor was not detected during initialization of the cassette shade drive
4130	Error moving the suck bar	The suck bar did not arrive in its new position during the expected time
4133	Error lowering the suck bar	The suck bar is not at its bottom position as expected
4134	Error moving the suck bar	The suck bar is not at the middle position as expected
4135	Error lifting the suck bar	The suck bar is not at the top position as expected
4136	Error moving the suck bar	The suck bar does not move
4137	Error setting the suck bar parameters	A command to the suck bar returned an invalid command
4138	While separating, double sheet error Paper under plate occurred several times without a plate being present	While separating, double sheet error Paper under plate occurred several times without a plate being present
4139	A piece of paper, located on the Jalousie, couldn’t fix by the suck bar	A piece of Paper couldn’t move from the suck bar to the Jalousie suction bar
4140	Error setting the separator ejector parameters	Invalid command encountered when enabling the ejector’s blowing function
4141	Error setting the separator ejector parameters	Invalid command encountered when enabling the ejector’s suction function
4142	Error setting the separator ejector parameters	Invalid command encountered when actuating the compressed air supply of the ejector’s suck bar
4143	Error setting the separator ejector parameters	Invalid command encountered when actuating the compressed air supply of the ejector’s suction bar
4144	Vacuum error signaled by vacuum sensor. Unable to suck and hold the material or material lost	The vacuum sensor of the separator detected an insufficient vacuum
4152	Error setting the double sheet sensor parameters	Invalid command encountered when selecting the double sheet sensor
4153	No or not enough compressed air	Poll of compressed air status result: no compressed air
4154	Error separating. A double sheet detected cannot be separated because the suction bar is carrying material already
4155	A double sheet detected on the jalousie. The material could not be separated	The double sheet must be removed manually by hand
4156	A double sheet was detected on the Jalousie. The material couldn’t be split	The double sheet couldn’t fix by the suck bar – it must be removed by hand
4157	A double sheet was detected on the Jalousie. The material couldn’t be split	The double sheet couldn’t fix by the suck bar – it must be removed by hand
4161	Tray empty. No material on the active tray	No material found when reading the tray fill level
4162	A detected double sheet on the Jalousie couldn’t move to the Load Table	A double sheet wasn’t detected from the exit-sensor of the separator
4163	A double sheet was detected on the Jalousie. The material couldn’t be split within several tries	The double sheet couldn’t be split within several tries – it must be removed by hand
4164	While checking the material at the suction bar, an error with the vacuum occurred
4165	While sucking the paper with the suck bar, a vacuum error occurred	There was no vacuum at the suction bar
4166	The paper could not be removed, because the cassette was not open
4167	While loading and locking the cassette an error occured inside the SCL
4171	Clamp jaw unit error	Unable to close the clamp jaw
4172	Clamp jaw unit error	Unable to open the clamp jaw unit – the unit will not release the plate
4173	Error closing the clamp jaw unit	Unable to close the clamp jaw unit during the expected time
4174	Error closing the clamp jaw unit	Unable to open the clamp jaw unit during the expected time
4181	No material found in the cassette	No material was detected during check of cassette level
4182	Almost no material in the cassette	A check of the cassette level detected only a few plates still in the cassette. The number has fallen below the set alert level
4183	The waste container is full	A check of the waste container level detected that the container is full
4184	The waste container is almost full	A check of the waste container level detected that the set alert level was exceeded
4190	Error setting the waste container parameters	Invalid command encountered when opening / closing the waste container
4191	Unable to open the waste container	The waste container could not be opened because it was impossible to move the shutter into the specified position
4192	Waste container open	Could not open the cassette because the waste container was not closed
4193	Vacuum error at the suction bar. Could not suck the material to the bar or the material was lost	Vacuum sensor detected that the vacuum was too low when the suction bar of the separator was used
4194	Vacuum error after raising the suction bar. Could not suck the material to the bar or the material was lost	Vacuum sensor detected that the vacuum was too low after raising the suction bar
4195	Configuration error – unknown machine type	Invalid machine type set
4196	Error separating	Plate lost while separating or during transport to the entry of the load table plate. The plate did not arrive at the relevant sensor
4197	Error separating	Material lost when lifting it out of the tray
4198	An error occurred during initialization or error handling. Material was found on the shutter	Material was found on the shutter during initialization or error handling. The material is to be removed by the operator
4201	Unable to determine the position of the load table plate	Both load table plate position sensors output the same signal
4202	Error moving the load table	Timeout encountered when swivelling/moving the load table
4203	The load table fans are not working
4204	Error moving the plate holder	Timeout encountered when lifting/lowering the plate holder
4205	Error initializing the plate holder	The plate holder did not move away from its init sensor
4206	Error initializing the plate drive motor	The plate holder did not move up to its init sensor
4207	Error initializing the plate drive motor	Initialization of the plate drive motor failed. Absolute positioning of the plate holder is not possible
4208	No plate on the load table	The procedure requires a plate but none has been detected
4209	Error initializing the center unit	The center unit did not move away from its init sensor
4210	Error initializing the center unit	The center unit did not move up to its init sensor
4211	Material transport error	Error transporting the plate from the load table to the conveyor
4212	Plate not in the gripper	The plate did not move up to the grip sensor
4213	The plate did not move up to the grip sensor	Wrong width of plate. See the log file for further details
4214	Load table process error	A signal expected from the load table holder sensor not received
4215	Error initializing the load table	The states of the load table sensors have been checked. The result is an impossible combination
4226	Double sheet detected on load table during material transport to recorder	Please remove the material manually by hand
4227	The load table can not be moved, because material was detected between separator and load table	Material was detected in light barrier of the separator. The material is to be removed by the operator before moving the load table
4301	Error moving the conveyor	Timeout lifting/lowering the conveyor table
4302	Error initializing the conveyor roller motor	Initialization of the conveyor roller motor failed
4303	Error transporting the plate from the conveyor to the load table	Plate transport from the conveyor to the load table is not possible. The plate has left the range of the entry sensor already
4304	Error centering the plate on the conveyor	Unable to fully load the plate onto the conveyor. The conveyor entry sensor is not free
4305	No plate on the conveyor	The procedure requires a plate but none has been detected
4306	Configuration error – no valid assembly position of the online processor	Assembly position of the online processor wrong or not specified
4307	Error centering the plate on the conveyor	Conveyor center sensor not enabled
4308	Error initializing the conveyor slider	The conveyor slider did not move away from its init sensor
4309	Error initializing the conveyor slider	The conveyor slider did not move up to its init sensor
4310	Error initializing the conveyor slider	Initialization of the conveyor slider motor failed
4311	Error unloading the plate	Signal expected from the conveyor entry sensor not received
4312	Conveyor process error	Signal expected from the conveyor slider init sensor not received
4313	Error actuating the online processor	No ON signal of the online processor
4314	Error actuating the online processor	No connect signal of the online processor
4315	Configuration error – wrong online processor interface set	The set online processor interface is unknown
4316	Error unloading the plate	Error centering the plate on the conveyor. The computed correction exceeds the maximum
4317	Error unloading the plate	Signal expected from the conveyor exit sensor not received
4318	Error unloading the plate	Signal expected from the conveyor center sensor not received
4319	Error initializing the conveyor	The states of the conveyor sensors have been checked. The result is an impossible combination
4320	Error centering the plate on the conveyor	Unable to readjust the plate onto the conveyor. The plate is expected on the entry sensor but isn’t there
4401	An error occurred while swinging out the cassette drive	One of the two cassette drives did not reach its swing-out position in the allotted time
4402	An error occurred while swinging out the cassette drive	One of the two cassette drives did not leave its swing-out position in the allotted time
4403	An error occurred during the cassette drive setup	An invalid command for the cassette drive was detected
4404	An error occurred while evaluating the current cassette position	The sensors for the horizontal cassette position returned an invalid position
4405	No cassette was detected at the MCL exit when conveying a cassette from the SCL to the MCL	The exit sensor of the MCL did not detect a cassette
4406	No cassette was detected at the MCL entry when loading a cassette	The cassette drive sensor (perhaps the entry sensor as well) did not detect a cassette
4407	No fully loaded cassette was detected while unloading a cassette from the MCL
4408	A cassette could not be positioned correctly while loading it from the SCL	The specified number of attempts to position the cassette was exceeded
4409	A cassette could not be positioned correctly while loading it from the trolley	The specified number of attempts to position the cassette was exceeded
4410	Error closing the inlet door	The inlet door did not reach the position in the allotted time
4411	Error opening the inlet door	The inlet door did not reach the position in the allotted time
4412	An error occurred while evaluating the current inlet door position	The sensors for the inlet door position returned an invalid position
4413	An error occurred during the setup of the inlet door drive	An invalid command for the inlet door drive was detected
4414	The inlet door was not open before a cassette was unloaded to the trolley
4415	The inlet door was not closed before the elevator moved
4420	Error initializing the elevator	The elevator init sensor was not reached
4421	Error initializing the elevator	The elevator init sensor was not left
4422	An error occurred while evaluating the current elevator position	The sensors for the vertical cassette position detected an invalid position
4423	Failed to find cause of aborted movement after elevator or cassette drive finished moving	The cause was an undefined event
4424	The elevator or cassette drive did not finish moving by reaching a sensor
4425	An error occurred while moving the elevator	The error bit of the elevator motor is active
4426	A safety error occurred before the elevator moved	One of the two cassette drives is not swung out
4427	A safety error occurred before the elevator moved	The cassette in the SCL was not locked
4428	An error occurred while evaluating the current elevator position	The sensors for the vertical cassette position returned an invalid position
4429	An error occurred during the elevator setup	An invalid command for the elevator was detected
4440	No fully loaded cassette was detected before unloading a cassette from the MCL to the SCL or the trolley
4441	No fully loaded cassette was detected after loading a cassette from the SCL or the trolley to the MCL
4442	No cassette was detected at the MCL entry sensor before loading a cassette from the SCL to the MCL
4443	No cassette was detected at the MCL exit sensor after unloading a cassette from the MCL to the SCL
4444	No cassette was detected at the MCL entry sensor before loading a cassette from the trolley to the MCL
4445	No cassette was detected at the MCL entry sensor after unloading a cassette from the MCL to the trolley
4446	A cassette was detected to be not fully loaded to its position before the elevator moved
4447	The cassette is not in valid position
4448	No trolley was found in front of the MCL before unloading a cassette from the MCL
4449	A cassette was detected in the SCL before unloading a cassette from the MCL to the SCL
4450	The elevator could not be moved or movement had to be stopped too soon because the cassette drive was no longer swung out
4451	An error occurred, at least one safety relay of the MCL is open
4460	Movement of elevator started, duration approximately 90 sec
4461	Movement of elevator started, duration approximately 60 sec
4462	Movement of elevator started, duration approximately 30 sec
4500	No tray with the requested material	Further processing will be paused until a tray with the requested material has been put in
4501	The waste container is open	Further processing will be paused until the waste container has been closed
4502	The load table is not free. The system may be waiting for a plate to be moved on into the online processor	Further processing will be paused until the load table is free again
4503	The conveyor is not free. The system may be waiting for a plate to be moved on into the online processor	Further processing will be paused until the conveyor is free again
4504	The trolley is not in loading/unloading position	Further processing will be paused until the trolley is in the correct position
4505	Online processor not ready – no connect signal	Further processing will be paused until a connect signal has been received from the online processor
4506	The online processor is off	Further processing will be paused until the online processor is on and has sent a ready signal
4507	The online processor is busy	Further processing will be paused until the state of the online processor has changed from Busy to Not Busy
4508	The paper container is full	Further processing will be paused until the paper container has been opened and emptied
4509	Tray empty	Further processing will be paused until the tray has been removed, filled with material and put back in
4510	No or not enough compressed air	Further processing will be paused until the pressure level has reached the required value
4511	Remove the cassette	Further processing will be paused until the cassette has been removed
4512	Insert required plate to bypass	Insert required plate to bypass
4513	Remove plate from bypass. Plate width is not as requested	Remove plate from bypass
4520	Shaft data inconsistency detected. Rescan initiated (approx. 120 sec.)
4530	Error executing comand	The DAL command is not implemented
4531	Error executing command	The DAL command was rejected
4532	Error loading/unloading a cassette	Loading/unloading the cassette to the specified tray was impossible as the tray already contained a cassette
4533	Error loading/unloading a cassette	The specified tray number is out of ra
4534	Error loading/unloading a cassette	The specified tray type is incorrect
4535	Error loading/unloading a cassette	The state of the specified tray is incorrect
4536	Initialization failed	The initialization loop exceeded the maximum
4537	Error Correction failed	The error correction loop exceeded the maximum
4538	Shut down failed	The shutdown loop exceeded the maximum
4988	An error was detected in the horizontal drive of the MCL	The elevator’s motor control detected an error and switched itself off
4989	Error initializing a motor	Unable to quit the home sensor
4990	Error initializing a motor	Expected home sensor not found at the target position
4991	Error controlling a motor	Expected sensor not found at the target position
4992	Error controlling a motor	Invalid parameter found when computing the data for stepper motor actuation
4993	Error controlling a motor	No actuation data found when starting the stepper motor
4994	Error controlling a motor	Insufficiently larger memory range found when computing the data for stepper motor actuation
4995	Error controlling a motor	Absolute motor positioning not possible, the motor is to be initialized first
4996	Error controlling a motor	Timeout actuating the stepper motor
4997	Error controlling a motor	Invalid minimum frequency for actuating the stepper motor
4998	Error controlling a motor	Invalid parameter found when computing the data for stepper motor actuation
4999	Error controlling a motor	Error computing the data for actuating the stepper motor

Topsetter 74 / Acento II / Screen PT-R4xxx

Computer to Plate

Error: Description:

Ex101		Nip roller does not ascend
Ex102		Nip roller does not descend
Ex103		Transport unit does not ascend
Ex104		Transport unit does not descend
Ex105		Trail clamp arm does not ascend
Ex106		Trail clamp arm does not descend
Ex107		Squeeze roller does not descend
Ex108		Squeeze roller does not ascend
Ex109		Trail clamp cannot be locked. PH24-1/2 or M24 is illegal
Ex10a		Trail clamp cannot be unlocked. PH24-1/2 or M24 is illegal
Ex10b		Balancer drive pin cannot be initialized
Ex10c		Both of the Home and Away side drive pins for the balancer can not be pulled out
Ex10d		Both of the Home and Away side drive pins for the balancer can not be inserted
Ex10e		Bar for releasing the lead clamp does not ascend
Ex10f		Bar for releasing the lead clamp does not descend
Ex110		Shutter does not open
Ex111		Shutter does not close
Ex112		Plate size (in the Y direction) is shorter than the set value
Ex113		When the plate is unloaded, the plate pass sensor (PH54-2) does not switch to ON
Ex114		Not bring down squeeze at loading
Ex115		Plate size (in the Y direction) is longer than the set value
Ex116		Servo status is illegal
Ex117		Servo status is error
Ex118		Servo alarm
Ex11a		Drum speed is set beyond the permitted rate of the servo controller
Ex11b		Current drum’s encoder pulse is beyond 4000
Ex11c		Error has occurred during drum positioning
Ex11d		When the clamp is locked, some tail clamps are detected on the clamp arm, or when the clamp is unlocked, some tail clamps are not detected on the clamp arm
Ex11e		Drum’s encoder pulse is beyond the permitted range after drum positioning
Ex11f		Plate cannot be transferred into the transport unit
Ex120		Home side balancer pin cannot be detected before insertion
Ex121		Home side balancer pin cannot be detected before pulled out (The balancer is not moving).
Ex122		Clamp arm and squeeze roller do not descend
Ex123		Trail clamp is half-locked
Ex124		The plate passing-sensor for unloading (PH54) does not switch to ON
Ex125		Time-out error has occurred when the squeeze roller ascends and clamp cam
Ex126		There was no plate to move to the shutter
Ex127		Servo controller does not enter the “Ready” status
Ex128		The balancer search sensor has not detected a balancer
Ex129		Error has occurred on the Home side of the alignment plate (while the alignment plate is returning to its origin)
Ex12a		Error has occurred on the Away side of the alignment plate (while the alignment plate is returning to its origin)
Ex12b		Error has occurred on the Home and Away sides of the alignment plate (while the alignment plate is returning to its origin)
Ex12c		Error has occurred on the Home side of the alignment plate (while alignment is performed)
Ex12d		Error has occurred on the alignment plate (while alignment is performed)
Ex12e		Error has occurred on the Home and Away sides of the alignment plate (when alignment is performed)
Ex12f		Plate has not transferred to the punch unit
Ex130		Plate does not leave the punch unit
Ex131		Time-out error has occurred when Punch 1 is activated
Ex132		Time-out error has occurred when Punch 2 is activated
Ex133		Time-out error has occurred when Punch 3 is activated
Ex134		Time-out error has occurred when Punch 4 is activated
Ex135		Time-out error has occurred when Punch 5 is activated
Ex136		Time-out error has occurred when Punch 6 is activated
Ex137		Time-out error has occurred when Punch 7 is activated
Ex138		Time-out error has occurred when Punch 8 is activated
Ex139		After a plate is transferred to the gripper clamp, the plate detection sensor (PH29H/A) does not switch to ON
Ex13a		When the clamp arm is lowered, the sensor (to detect whether the clamp arm pins are hooked on the clamp properly) has been turned ON.(Home side)
Ex13b		The specified encoder pulse for the drum is beyond 4000
Ex13c		The transport unit’s Away side is not moving during its operation
Ex13d		The transport unit’s Home side is not moving during its operation
Ex13e		Error has occurred on the Home side of the alignment plate (while the alignment plate is finely returning to its origin)
Ex13f		Error has occurred on the Away side of the alignment plate (while the alignment plate is finely returning to its origin)
Ex140		Error has occurred on the Home and Away side of the alignment plate (while the alignment plate is returning to its origin)
Ex141		A plate remains in the transport unit when the machine received a request command
Ex142		A plate remains in the transport unit during error handling
Ex143		A plate remains on the discharge table in the transport unit
Ex144		A plate remains on the insertion table in the transport unit
Ex145		Plate cannot be moved onto the discharge table during initialization
Ex146		Plate cannot be moved onto the insertion table
Ex147		Balancer search operation has not been completed properly
Ex148		When the transport unit descends, only the Home side Down sensor in the transport unit is turned ON
Ex149		When the transport unit descends, only the Away side Down sensor in the transport unit is turned ON
Ex14a		When the transport unit ascends, only the Home side UP sensor in the transport unit is turned ON
Ex14b		When the transport unit ascends, only the Away side UP sensor in the transport unit is turned ON
Ex14c		Front, rear or side cover is open. (Some interlock switches are OFF)
Ex14d		A fuse on the relay board was blown. (home)
Ex14e		Thumbscrew is not tightened securely on the rear cover. (The servo stop switch is ON)
Ex14f		A plate exists on the discharge table in the transport unit during initialization
Ex150		A plate exists on the insertion table in the transport unit during initialization
Ex151		Number of balancers is not sufficient. (The number of balancers checked by the balancer search sensor was one, two or three for both the Home and Away sides)
Ex152		Clamp arm is not in the UP position
Ex153		A fuse on the relay board was blown. (away)
Ex154		Blower is turned off, but signal does not change
Ex155		Tail clamps are missing during initialization
Ex156		The size check program of the cetering function detects that the measured plate size is longer than the expected one
Ex157		The size check program of the cetering function detects that the measured plate size is shorter than the expected one
Ex158		Both of Home and Away size check sensors are on before starting the centering program
Ex159		Auto-loader is stopped by a interlock OFF
Ex15a		This hardware matching is illegal
Ex15b		The balancer is not moved to the target position
Ex15c		The drum can not be spun up because the Home-Upper sensor of the Lead clamp release bar is off
Ex15d		During plate loading, double plate loading is detected
Ex15e		The loaded plate is detected to be floating while drum spinning
Ex15f		The drum cannot be spun up because the Upper sensor of the clamp arm is off
Ex160		The drum can not be spined up because the Home-Upper sensor of the clamp arm is off
Ex161		The drum cannot be spun up because the balancing pin on the (Away side) is not in the waiting position
Ex162		The drum cannot be spun up because the balancing pin on the (Home side) is not in the waiting position
Ex163		The drum cannot be spun up because the Upper sensor of the squeeze roller is off
Ex164		The drum can not be spun up because the Away-Upper sensor of the Lead clamp release bar is off
Ex165		The drum is rotated to the “lead clamp position”, but the status of the Servo controller (SVC) has not changed to “Ready”
Ex166		The drum is rotated to the “tail clamp position”, but the status of the Servo controller (SVC) has not changed to “Ready”
Ex167		The drum is rotated to the “squeeze position”, but the status of the Servo controller (SVC) has not changed to “Ready”
Ex168		The drum is rotated to the “balance pin before inserted”, but the status of the Servo controller (SVC) has not changed to “Ready”
Ex169		The drum is rotated to the “balance pin after inserted”, but the status of the Servo controller (SVC) has not changed to “Ready”
Ex16a		The drum is rotated to the “pick up tail clamp position”, but the status of Servo controller (SVC) has not changed to “Ready”
Ex16b		The drum is rotated to the “plate removal position”, but the status of the Servo controller (SVC) has not changed to “Ready”
Ex16c		SVC Error has occurred during drum positioning for the lead clamp
Ex16d		SVC Error has occurred during drum positioning for the tail clamp
Ex16e		SVC Error has occurred during drum positioning for the squeeze
Ex16f		SVC Error has occurred during drum positioning for the balance pin insertion
Ex170		SVC Error has occurred during drum positioning for the balance pin pull out
Ex171		SVC Error has occurred during drum positioning for the picking up tail clamp
Ex172		SVC Error has occurred during drum positioning for the plate removal
Ex173		Time-out error has occurred during drum positioning (Lead clamp position)
Ex174		Time-out error has occurred during drum positioning (Tail clamp position)
Ex175		Time-out error has occurred during drum positioning (Squeeze position)
Ex176		Time-out error has occurred during drum positioning (Balance pin before inserted)
Ex177		Time-out error has occurred during drum positioning (Balance pin after inserted)
Ex178		Time-out error has occurred during drum positioning (Pick up tail clamp)
Ex179		Time-out error has occurred during drum positioning (Plate removal)
Ex17a		After verifying the removal of the plate, press the OK button. When the OK button is pressed, initialization begins
Ex17b		PH62A-sensor is illegal. The sensor detects a plate during initialization
Ex17c		PH29H-sensor is illegal. The PH29H-sensor does not turn ON during initialization
Ex17d		PH61H-sensor is illegal. The sensor detects a plate during initialization
Ex17e		PH61A-sensor is illegal. The sensor detects a plate during initialization
Ex17f		PH29A-sensor is illegal. The PH29A-sensor does not turn ON during initialization
Ex180		Drum does not start rotating at high-speed
Ex181		Drum does not rotate at the specified high-speed
Ex182		Error has occurred after the drum rotated at the specified high-speed
Ex183		Drum cannot be stopped when rotating at high-speed
Ex184		Drum operation is stopped with an emergency stop command
Ex185		Drum operation is stopped with an abort command
Ex186		Drum’s vacuum pressure is not sufficient. Please confirm connection of the blower-hose, or the Vacuum-sensor is illegal
Ex187		Error has occurred on the blower, or the power supply of the blower is OFF
Ex188		Drum operation is stopped due to low pressure in the drum
Ex189		Door is open
Ex18a		Door does not open
Ex18b		Transport tasks: Parameter error
Ex18c		Error has occured on the blower. Please turn off this machine, and turn on after waiting 10 seconds. Also, confirm whether or not the connector doesn’t come off
Ex18d		The drum can not be spun up, because some of the interlock switches are OFF, or some of the actuator’s sensors are damaged, or the blower is damaged
Ex18e		Door does not open, because some of the interlock switches are OFF (front cover or rear cover is open)
Ex190		Clamp arm does not descend (Home side)
Ex191		Clamp arm does not descend (Away side)
Ex192		Clamp arm does not ascend (Home side)
Ex193		Clamp arm does not ascend (Away side)
Ex194		When the clamp arm is lowered, the sensor (to detect whether the clamp arm pins are hooked on the clamp properly) has been turned ON (Away side)
Ex195		Trail clamp cannot be locked (Home side)
Ex196		Trail clamp cannot be locked (Home side)
Ex197		Trail clamp cannot be unlocked (Home side)
Ex198		Trail clamp cannot be unlocked (Away side)
Ex199		Balancer drive pin cannot be inserted (Home side) Either of PH11-1H,PH11-2H or M11H is illegal
Ex19a		Balancer drive pin cannot be inserted (Away side) Either of PH11-1A,PH11-2A or M11A is illegal
Ex19b		Balancer drive pin cannot be pulled out (Home side) Either of PH11-1H,PH11-2H or M11H is illegal
Ex19c		Balancer drive pin cannot be pulled out (Away side) Either of PH11-1A,PH11-2A or M11A is illegal
Ex19d		Balancer pin cannot be detected before insertion (Away side)
Ex19e		Balancer pin cannot be detected before pull out (the balancer is not moving) (Away side)
Ex19f		The balancer search sensor has not detected a balancer.(Home side)
Ex1a0		The balancer search sensor has not detected a balancer.(Away side)
Ex1a1		Number of balancers is not sufficient. (Home side)
Ex1a2		Number of balancers is not sufficient. (Away side)
Ex1a3		Soft-interlock or drum-stop swtich is OFF during drum spinning
Ex1a4		The cover-interlock switch is OFF during drum
spinning Ex1a5		The interlock switch-3 is OFF during drum spinning
Ex1a6		A plate cannot be carried into the transport unit
Ex1a7		A plate cannot be carried to sensor PPH50-2
Ex1a8		Auto-loader is not turned on, or some interlock switches on Auto-loader are OFF. Please turn on Auto-loader, or all interlock switch
Ex1a9		Cassete carrier was removed. Please set cassette carrier
Ex1aa		The door of the cassette part is open
Ex1ab		Maintenance-cover of Auto-loader was opend. Please clode maintenance cover
Ex1ac		Bridge cover-2 was opened. Please clode bridge cover-2
Ex1ad		An interleaf under a plate was detected. Or a plate size (in the Y direction) is shorter than the set value
Ex1ae		An interleaf was detected on a plate. Or a plate size (in the Y direction) is shorter than the set value
Ex1b0		Trail clamp is not detected on the clamp arm before the plate loading
Ex1b1		Trail clamp is detected on the clamp arm before the plate unloading
Ex1b2		Trail clamp cannot be set correctly
Ex1b3		This plate can’t be transed. Because something error has occured when the transfering to AT
Ex1b4		This plate can’t be transed. Because trans path position is down
Ex1b6		The bridge-passing sensor does not turn OFF (for Jig mode)
Ex1b7		A plate remains on the plate detection sensor(PH70)
Ex1b8		When detects the front of a plate, the detection area is not brought
Ex1b9		When detects the front of a plate, the detection of Home or Away is not brought
Ex1ba		PH11-2H-sensor is illegal. The PH11-2H-sensor does not turn ON during initialization
Ex1bb		PH11-2A-sensor is illegal. The PH11-2A-sensor does not turn ON during initialization
Ex1c0		Lead clamp release bar cannot be driven. Either PH30H or PH31H is illegal
Ex1c1		Lead clamp release bar cannot be driven. Either PH30H or PH31H is illegal
Ex1c2		Trans path cannot be driven. Either PH55, PH56, or PH57 is illegal
Ex1c3		Trans path cannot be driven. Either PH56, or, PH57 is illegal
Ex1c4		Trans path cannot be driven. Either PH55, or, PH56 is illegal
Ex1c5		Trans path cannot be driven. Either PH55, or, PH57 is illegal
Ex1c6		Trail clamp arm cannot be driven. Either PH20 or PH21 is illegal
Ex1c7		Trail clamp arm cannot be driven. Either PH20 or M20 is illegal
Ex1c8		An interleaf was detected under a plate
Ex1c9		When centering alignment is performed, the plate set position is out of range
Ex1ca		Error has occured on the punching unit. The punch hole could not be opened correctly
Ex1cb		Opened shutter obstructs trans path driving
Ex1cc		Trail clamp arm obstructs trans path driving
Ex1cd		A plate remains in a machine
Ex1d0		Transfer operation is halted with an abort command
Ex1d1		Transport tasks are being processed
Ex1d2		Transport tasks are not being processed
Ex1d3		Transport tasks: Message order error
Ex1d4		Transport system is not initialized
Ex1e0		SVC user parameter breakdown
Ex1e1		SVC user parameter setting error
Ex1e2		SVC over-current
Ex1e3		SVC detection of regenerative error
Ex1e4		SVC postion error pulse overflow
Ex1e5		SVC Main circuit voltage error detection
Ex1e6		SVC over speed
Ex1e7		SVC overloaded (high load)
Ex1e8		SVC overloaded (low load)
Ex1e9		SVC stauts 99h
Ex1ea		SVC heat sink has overheated
Ex1eb		SVC stauts b1h
Ex1ec		SVC is out of control
Ex1ed		SVC phase error has been detected in the encoder
Ex1ef		SVC A and B phase for the encoder has broke down
Ex1f0		SVC C phase for the encoder has broke down
Ex1f1		SVC some phases of power line is open
Ex1f3		SVC An instantaneous loss of power has occurred
Ex1f4		SVC unknown error
Ex200		Exposure operation is interrupted with an abort command
Ex201		Exposure processing task is now processing another command
Ex202		Cancellation was requested while processing was not being performed
Ex203		PGON is not asserted
Ex204		START signal is not asserted
Ex205		START signal is not negated
Ex206		Test pattern; Data is not transferred
Ex207		Test pattern; Data transfer is not completed
Ex208		Reset procedure for RB31 board is not completed
Ex209		The set value for the drum rotation speed is too large
Ex20a		No plate edge is detected (when the plate edge sensor moves to the Away side)
Ex20b		No plate edge is detected (when the plate edge sensor is returning to the Home side)
Ex20c		Recording head has traveled beyond the limit (on the Away side)
Ex20d		Recording head has traveled beyond the limit (on the Home side)
Ex20e		Recording head positioning range error
Ex20f		Recording head has not been positioned at its origin. (Origin sensor does not turn OFF)
Ex210		Recording head has not been positioned at its origin. (Origin sensor does not turn ON)
Ex211		Emergency stop is requested for the secondary-scanning motor
Ex212		Secondary-scanning motor is deactivated with an abort command
Ex213		Secondary scanning motor is illegal
Ex214		Exposure in the secondary scanning direction exceeds the effective image ouput range
Ex215		FPGA sequence error
Ex216		Time-out error has occurred when the secondary scanning motor is activated
Ex217		EZ search has not detected the ORG sensor
Ex218		EZ search has not detected the EZ sensor
Ex219		When the CAL sensor search was executed, the maximum light intensity was less than 50 mW
Ex21a		Light intensity at the measurement starting point was at maximum when the CAL sensor search was executed
Ex21b		Light intensity at the measurement end point was at maximum when the CAL sensor search was executed
Ex21c		Over travel at recording head’s Home side when the CAL sensor search was executed
Ex21d		Test pattern parameter error
Ex21e		PGON signal is not negated
Ex21f		Secorndary direction origin point setup procedure failure.(The calibrated origin point is not the same as logical origin point)
Ex220		After an image data transfer from RIP is interrupted, it isn’t resumed
Ex221		Drum rotation error was detected. This plate will be unloaded because it could not be exposed correctly
Ex300		Both of plate pad and paper pad are not in original point
Ex301		After an interleaf is removed, plate cannot be detected
Ex302		An interleaf was detected on a plate. Or a plate size (in the Y direction) is shorter than the set value
Ex303		Plate pad cannot be initialized
Ex304		Plate pad cannot carry a plate
Ex305		While carring a plate, the plate pad dropped the plate
Ex306		Paper pad cannot be initialized
Ex307		Air pressure in the plate pad does not go down
Ex308		Air pressure in the paper pad does not go down
Ex309		PCL time-out error has occurred when plate pad was moved
Ex30a		PCL time-out error has occurred when paper pad was moved
Ex30b		Time-out error has occurred when plate pad was moved by stepping
Ex30c		Time-out error has occurred when paper pad was moved by stepping
Ex30d		A plate cannot be carried into the transport unit
Ex30e		PH90 does not switch to ON while removing the interleaf
Ex30f		PH90 does not switch to OFF while removing the interleaf
Ex310		Maintenance cover of auto-loader is open. Please close maintenance cover
Ex311		Bridge cover-2 of auto-loader is open. Please close bridge cover-2
Ex312		Cassette carrier is not set. Please set cassette carrier
Ex313		A plate remains in the bridge unit
Ex314		An interleaf remains in the paper exit
Ex315		Nip roller does not ascend
Ex316		Nip roller does not descend
Ex317		Auto-loader is not turned on, or some interlock switches on Auto-loader are OFF. Please turn on Auto-loader, or all interlock switch
Ex318		A plate cannot be carried to the bridge-passing sensor
Ex319		The plate pad went down from the original point
Ex31a		The paper pad went down from the original point
Ex31b		Maintenance-cover of Auto-loader was opend. Please clode maintenance cover
Ex31c		Bridge cover-2 was opened. Please clode bridge cover-2
Ex31d		Door was opened. Please close the door
Ex31e		Cassete carrier was removed. Please set cassette carrier
Ex31f		The paper pad dropped the interleaf while carrying the it
Ex320		Plate pad dropped a plate before the plate pad reached the intermediate sensor
Ex321		An interleaf in front of a plate was detected
Ex322		A plate remains on the sensor-2 of the bridge
Ex323		Intermediate sensor is OFF
Ex324		Power switch was turned off while Auto-loader was moving
Ex325		A plate cannot be carried to the intermediate sensor
Ex326		An interleaf under a plate was detected. Or a plate size (in the Y direction) is shorter than the set value
Ex327		The bridge-passing sensor does not turn OFF (for Jig mode)
Ex328		Door is open
Ex32c		The nip-roller for paper discharge cann’t be opened
Ex340		Door is open
Ex341		The interlock switch-3 is OFF
Ex342		The interlock switch-2 is OFF
Ex343		The interlock switch-1 is OFF
Ex344		A fuse on the relay board at home side has blown
Ex345		A fuse on the relay board at away side has blown
Ex346		Nip roller does not descend
Ex347		Nip roller does not ascend
Ex348		Shutter does not open
Ex349		Shutter does not close
Ex360		A plate remains on the bridge’s sensor-1
Ex361		No plate exists on the bridge’s sensor-3
Ex362		A plate remains on the bridge’s sensor-3
Ex363		A plate size in the Y direction is too long when its transferring to the AT
Ex364		A plate size in the Y direction is too short when its transferring to the AT. Or an interleaf in front of a plate was detected
Ex365		After the paper pad is descended, the metal sensor does not switch to ON
Ex366		Plate pad dropped the plate, before this initialize
Ex367		A teaching of plate size in the Y direction (1st) is finished
Ex368		A teaching of plate size in the Y direction (2nd) is finished
Ex369		This plate can’t be transed. Because something error has occured when transfering to AT
Ex36a		Air pressure in the plate pad does not go down after retry
Ex36b		A plate remains on the insertion table in the transport unit
Ex36c		This plate is judge as a paper during judgement operation
Ex36d		This plate can’t be transed. Because trans path position is down
Ex380		The door of the cassette part is open
Ex381		Time-out error has occurred when lift was initialized
Ex382		Time-out error has occurred when lift was moved
Ex383		Though the lift was initialized, the origin sensor is not ON
Ex384		The lift is not in the position where it is specified
Ex385		Already, there has been a cassette on the lift
Ex386		There are some cassettes which aren’t being set properly
Ex387		MA-L can’t be initialized because some cassettes are not in the lift or the cassette properly
Ex388		There is no cassette in the specified cassette slot
Ex389		There is no cassette on the lift
Ex38a		Lift has traveled beyond the limit (on the Up side)
Ex38b		Lift has traveled beyond the limit (on the Down side)
Ex38d		A cassette is already in the place to return a cassette
Ex38e		A lift can’t be raised and lowered because some cassettes are not in the lift or the cassette properly
Ex38f		Time-out error has occurred when a cassette was moved to cassette part
Ex390		Time-out error has occurred when a cassette was moved to lift
Ex391		Either plate pad or paper pad is not in original point
Ex392		An ineffective cassette number was indicated
Ex393		Cassette has traveled beyond the limit (on the Lift side)
Ex394		Cassette has traveled beyond the limit (on the Cassette side)
Ex395		MA-L can’t be initialized because some cassettes can’t be returned to the origin
Ex396		Though there is a cassette on the lift, the place to return the cassette isn’t vacant
Ex397		Though the movement of the lift was finished, the lift position sensor at the target position is not on
Ex398		MA-L Servo alarm
Ex399		Time-out error has occurred when arm was moved
Ex39a		Time-out error has occurred when a cassette was moved to cassette part by arm
Ex39b		Arm jut-out sensor (LS210E) is off
Ex39c		A cassette is in illegal position of the cassette slot
Ex39d		Arm is not in original point
Ex39e		SQ210A sensor is illegal
Ex400		Plate has already been loaded
Ex401		Plate has not been loaded
Ex402		Door is open
Ex403		Dump interleaves from the collection box
Ex600		Either the conveyor, processor, or stocker is not turned on, or is in the busy status or error status
Ex601		Either the conveyor, processor, or stocker is not turned on, or is in the busy status or error status
Ex602		The plate cannot be transferred into the AT unit
Ex603		The plate cannot be transferred completely into the AT unit
Ex606		Error
Ex607		Busy
Ex608		Error
Ex609		Busy
Ex60a		Error
Ex60b		Busy
Ex60c		Error occurred in ATM while a plate was carried to ATM
Ex80c		The result of the calculation “Initial value + increment value * (repetition – 1)” exceeds the upper limit value
Ex80d		(The result of the calculation “Exposure starting point + (pattern width + gap) * (repetition – 1)” exceeds the plate size
Ex80e		The specified plate is not linked with the printing-machine’s data
Ex80f		Perform initialization at the service screen
Ex810		No plate is set at inlet of transport unit
Ex811		Plate (printer) size specified by the host computer is not registered
Ex812		Image size specified by host computer is larger than allowable output image size
Ex813		Current offset of printing machine settings cause image to extend off plate
Ex814		Current paper-position of printing machine settings cause image to extend outside of allowable exposure area
Ex816		Some LD is nearing the end of its usable life
Ex817		There are some punch blocks, which have been used for more than the endurance time
Ex819		It failed to read the cassette number. It considers that the cassette number is No.1
Ex81a		Some LD’s cannot be calibrated to the target power. These LD’s be calibrated to lower target power
Ex81b		Some LD’s cannot be calibrated to the target power. Temporary to work half channels of recording head
Ex81c		Some LD’s cannot exposed by setting power due to be calibrated to lower target power
Ex81d		The temperature of the environment is greater than 28degrees
Ex81e		The temperature of the environment is less than 18degrees
Ex81f		Sensor for the temperature of the environment has not been connected
Ex820		Trail clamps are nearing the end of its usable life
Ex821		Trail clamps have been used for more than the endurance time
Ex822		Backup/restore of the data on NVRAM can’t be performed, because the Dip-Sw 2 is not on
Ex823		The backup of the data on NVRAM is not in Flash-Memory
Ex824		Calibration must be done because there is some LD which doesn’t reach the target power. But, LD calibration can not processed because temperature of LD block is too low
Ex825		The direction where a connected conveyer can’t be changed is set up in the plate types setting
Ex826		No response was returned from the conveyor
Ex827		An error was returned from the conveyer toward the switching command
Ex828		The conveyer can’t be changed to the direction that is set up in the plate types setting
Ex82a		Since the light intensity of laser diodes is detected as having deviated more than +-5% from the specified value, the equipment executes the calibration
Ex82b		Communication with the RAS server was interrupted. (RAS server was turned off, or RS-232C cable was drawn out)
Ex82c		No response come from DNS
Ex82d		Communication with the RAS server has resume
Ex82e		It failed in the connection to the rotating light server
Ex82f		The name of the mail server isn’t right
Ex830		It failed in the connection to the mail server
Ex831		Mail account was rejected
Ex832		An error occurred in the transmission of DATA command
Ex833		An error occurred in the transmission of header
Ex834		An error occurred in the transmission of body
Ex835		An error occurred in the transmission of attached file
Ex836		An error occurred in the transmission of TO command
Ex837		A command was sent to the SMTP server. But, no answer was returned from the server
Ex839		The cable between RB31 board and recording head is disconnected
Ex880		Servo pack: Time-out error occurred while receiving data
Ex881		Servo-Pack:Address error
Ex882		Servo-Pack:Data error
Ex883		Servo-Pack:Check sum error
Ex884		Servo-Pack:Undefined error code
Ex885		Servo-Pack:Number of received characters are insufficient
Exe01		Excessive current in the LD drive (driver 1 board)
Exe02		Excessive current in the LD drive (driver 2 board)
Exe03		Excessive current in the LD drive (driver 3 board)
Exe04		Excessive current in the LD drive (driver 4 board)
Exe05		Driver board temperature error or Head FPGA Version Error
Exe06		-5 V power supply error
Exe07		Calibration sensor is not connected
Exe08		Offset error in the calibration sensor
Exe09		Irregular 5 V power supply
Exe0a		Irregular +15 V power supply
Exe0b		Irregular -15 V power supply
Exe0c		Irregular 24 V power supply
Exe0d		Cover switch is OFF
Exe0e		BL command error (counter value is 0)
Exe0f		Zoom sensor is not detecting
Exe10		Focus sensor is not detecting
Exe11		Time has expired for home return.(Zoom or focus motor)
Exe12		Power supply irregular while the motor is driving
Exe13		Pulse motor has traveled beyond the limit. (Zoom or focus motor)
Exe14		Irregular power supply(instantaneous loss)
Exe20		Temperature of the LD block is greater than 28degrees
Exe21		Temperature at the periphery of the optical unit is greater than 35degrees
Exe22		Temperature of the radiating fin of the Peltier element is greater than 55 degrees
Exe23		Dew condensation error
Exe24		Sensor for LD block has not been connected
Exe25		Sensor for the periphery of the optical unit has not been connected
Exe26		Sensor for the radiating fin of the Peltier element has not been connected
Exe27		The dew condensation detection sensor has not been connected
Exe28		Temperature of the LD block is low
Exe30		Power supply error occurred when the recording head received the DW command
Exe31		Command error occurred when the recording head received the DW command
Exe32		Download error occurred when the recording head received the DP command
Exe33		Download error occurred when the recording head received the DP command
Exe34		Download address error occurred
Exe35		Error occurred when the recording head received the BU command
Exe36		Error occurred when the recording head received the BD command
Exe40		Writing error occurred when the recording head received the AC command
Exe41		Writing error on EEPROM
Exe42		RAM error
Exe43		ROM check sum error
Exe44		FPGA error
Exe45		Data error due to a divide-by-zero error
Exe60		LD Current setting Error
Exe61		The temperature of the LD block is greater than 28degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of the environment <= 28degrees)”
Exe62		The temperature of the LD block is greater than 28degrees (Temperature at the periphery of the optical unit <= 35degrees. Temperature of the environment > 28degrees)”
Exe63		The temperature of the LD block is greater than 28degrees (Temperature at the periphery of the optical unit <= 35degrees. Temperature of the environment > 28degrees)”
Exe64		The temperature at the periphery of the optical unit is greater than 35degrees (Temperature of the environment <= 28degrees)
Exe65		The temperature of the radiating fin is greater than 55degrees (Temperature at the periphery of the optical unit>35degrees. Temperature of the environment <= 28degrees)
Exe66		The temperature of the radiating fin is greater than 55degrees (Temperature at the periphery of the optical unit <= 35degrees)
Exe67		The LD block has dew. (Temperature of the LD block < 22degrees Temperature at the periphery of the optical unit >= 18degrees)
Exe68		The LD block has dew. (Temperature of the LD block < 22degrees Temperature at the periphery of the optical unit < 18degrees)
Exe69		The temperature of the LD block is less than 5degrees (Temperature at the periphery of the optical unit >= 17degrees)
Exe6a		The temperature of the LD block is less than 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of the environment >= 18degrees)
Exe6b		The temperature of the LD block is greater than 28degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of the environment <= 28degrees)
Exe6c		The temperature of the LD block is greater than 28degrees (Temperature at the periphery of the optical unit <= 35degrees. Temperature of the environment > 28degrees)
Exe6d		The temperature of the LD block is greater than 28degrees (Temperature at the periphery of the optical unit <= 35degrees. Temperature of the environment <= 28degrees)
Exe6e		The temperature inside the machine is greater than 35degrees (Temperature of the environment <= 28degrees)
Exe6f		The temperature of the radiating fin is greater than 55degrees (Temperature at the periphery of the optical unit>35degrees. Temperature of the environment <= 28degrees)
Exe70		The temperature of the radiating fin is greater than 55degrees (Temperature at the periphery of the optical unit <= 35degrees.)
Exe71		It is just before a recording head has dew (Temperature of the LD block < 22degrees. Temperature of the environment >=18degrees)
Exe72		It is just before a recording head has dew (Temperature of the LD block < 22degrees. Temperature of the environment < 18degrees)
Exe73		The temperature of the LD block is in between 5degrees and 17degrees (Temperature of the environment <= 18degrees)
Exe74		The temperature of the LD block is in between 5degrees and 17degrees (Temperature of the environment < 18degrees.)
Exea0		Light intensity adjustment error 0ch
Exea1		Light intensity adjustment error 1ch
Exea2		Light intensity adjustment error 2ch
Exea3		Light intensity adjustment error 3ch
Exea4		Light intensity adjustment error 4ch
Exea5		Light intensity adjustment error 5ch
Exea6		Light intensity adjustment error 6ch
Exea7		Light intensity adjustment error 7ch
Exea8		Light intensity adjustment error 8ch
Exea9		Light intensity adjustment error 9ch
Exeaa		Light intensity adjustment error 10ch
Exeab		Light intensity adjustment error 11ch
Exeac		Light intensity adjustment error 12ch
Exead		Light intensity adjustment error 13ch
Exeae		Light intensity adjustment error 14ch
Exeaf		Light intensity adjustment error 15ch
Exeb0		Light intensity adjustment error 16ch
Exeb1		Light intensity adjustment error 17ch
Exeb2		Light intensity adjustment error 18ch
Exeb3		Light intensity adjustment error 19ch
Exeb4		Light intensity adjustment error 20ch
Exeb5		Light intensity adjustment error 21ch
Exeb6		Light intensity adjustment error 22ch
Exeb7		Light intensity adjustment error 23ch
Exeb8		Light intensity adjustment error 24ch
Exeb9		Light intensity adjustment error 25ch
Exeba		Light intensity adjustment error 26ch
Exebb		Light intensity adjustment error 27ch
Exebc		Light intensity adjustment error 28ch
Exebd		Light intensity adjustment error 29ch
Exebe		Light intensity adjustment error 30ch
Exebf		Light intensity adjustment error 31ch
Exee0		Incorrect command has been input
Exee1		The temperature of the LD block is greater than 28degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of the environment > 28degrees)
Exee2		Temperature at the periphery of the optical unit is greater than 35degrees (Temperature of the environment > 28degrees)
Exee3		The temperature of the radiating fin is greater than 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of the environment > 28degrees)
Exee4		It is just before a recording head has dew (Temperature of the LD block >= 22degrees)
Exee5		The temperature of the LD block is less than 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of the environment < 18degrees)
Exee6		0-7ch in signal line is break detect
Exee7		8-15ch in signal line is break detect
Exee8		0-15ch in signal line or DOTCLK signal line is break detect
Exef0		Recording head processing task is now processing another message
Exef2		Recording head unit is not running
Exef3		Recording head data check sum error occurred when data was uploaded
Exef4		Recording head data address error occurred when data was uploaded
Exef5		LD calibration cannot process because temperature of LD block is too low
Exef6		A command was sent to the exposure head. But, no answer was returned from the exposure head
Exfa0		System error (stack overflow)
Exfa1		Floating point arithmetic error
Exfa2		Divide-by-zero error
Exfa3		System error (semaphore)
Exfb0		Flash memory erase error
Exfb1		Flash memory erase error (during verification)
Exfb2		Flash memory write error
Exfb3		Incompatible flash memory

Topsetter 102 screen pt r8xxx

Computer to Plate

Error: Description:

Ex101		Nip roller does not ascend
Ex102		Nip roller does not descend
Ex103		Transport unit does not ascend
Ex104		Transport unit does not descend
Ex105		Trail clamp arm does not ascend
Ex106		Trail clamp arm does not descend
Ex107		Squeeze roller does not descend
Ex108		Squeeze roller does not ascend
Ex109		Trail clamp cannot be locked
Ex10a		Trail clamp cannot be unlocked
Ex10b		Balancer drive pin cannot be initialized
Ex10c		Both of the Home and Away side drive pins for the balancer can not be pulled out
Ex10d		Both of the Home and Away side drive pins for the balancer can not be inserted
Ex110		Shutter does not open
Ex111		Shutter does not close
Ex112		Plate size (in the Y direction) is shorter than the set value
Ex113		When the plate is unloaded, the plate pass sensor (PH54-2) does not switch to ON
Ex114		Not bring down squeeze at loading
Ex115		Plate size (in the Y direction) is longer than the set value
Ex116		Servo status is illegal
Ex117		Servo status is error
Ex118		Servo alarm
Ex11a		Drum speed is set beyond the permitted rate of the servo controller
Ex11b		Current drum’s encoder pulse is beyond 4000
Ex11c		Error has occurred during drum positioning
Ex11d		When the clamp is locked, some tail clamps are detected on the clamp arm, or when the clamp is unlocked, some tail clamps are not detected on the clamp arm
Ex11e		Drum’s encoder pulse is beyond the permitted range after drum positioning
Ex11f		Plate cannot be transferred into the transport unit
Ex120		Balancer pin cannot be detected before inserted (Home side)
Ex121		Balancer pin cannot be detected before pulled out (the balancer is not moving) (Home side)
Ex122		Clamp arm and squeeze roller do not descend
Ex123		Clamp arm and squeeze roller do not ascend
Ex126		There was no plate to move to the shutter
Ex127		Servo controller does not enter the “Ready” status
Ex128		No balancer has been detected by the balancer search sensor
Ex129		Error has occurred on the Home side of the alignment plate (while the alignment plate is returning to its origin)
Ex12a		Error has occurred on the Away side of the alignment plate (while the alignment plate is returning to its origin)
Ex12b		Error has occurred on the Home and Away sides of the alignment plate (while the alignment plate is returning to its origin)
Ex12c		Error has occurred on the Home side of the alignment plate (while alignment is performed)
Ex12d		Error has occurred on the alignment plate (while alignment is performed)
Ex12e		Error has occurred on the Home and Away sides of the alignment plate (when alignment is performed)
Ex12f		Plate has not transferred to the punch unit
Ex139		After a plate is transferred to the gripper clamp, the plate detection sensor (PH25H/A) does not switch to ON
Ex13a		When the clamp arm is lowered, the sensor (to detect whether the clamp arm pins are hooked on the clamp properly) has been turned
Ex13b		The specified encoder pulse for the drum is beyond 4000
Ex13c		The transport unit’s Away side is not moving during its operation
Ex13d		The transport unit’s Home side is not moving during its operation
Ex13e		Error has occurred on the Home side of the alignment plate (while the alignment plate is finely returning to its origin)
Ex13f		Error has occurred on the Away side of the alignment plate (while the alignment plate is finely returning to its origin)
Ex140		Error has occurred on the Home and Away side of the alignment plate (while the alignment plate is returning to its origin)
Ex141		A plate remains in the transport unit when the machine received a request command
Ex142		A plate remains in the transport unit during error handling
Ex143		A plate remains on the discharge table in the transport unit
Ex144		A plate remains on the insertion table in the transport unit
Ex145		Plate cannot be moved onto the discharge table during initialization
Ex146		Plate cannot be moved onto the insertion table
Ex147		Balancer search operation has not been completed properly
Ex148		When the transport unit descends, only the Home side Down sensor in the transport unit is turned ON
Ex149		When the transport unit descends, only the Away side Down sensor in the transport unit is turned ON
Ex14a		When the transport unit ascends, only the Home side UP sensor in the transport unit is turned ON
Ex14b		When the transport unit ascends, only the Away side UP sensor in the transport unit is turned ON
Ex14c		Front, rear or side cover is open. (Some interlock switches are OFF)
Ex14d		A fuse on the relay board was blown. (home)
Ex14e		Thumbscrew is not tightened securely on the rear cover. (The servo stop switch is OFF)
Ex14f		A plate exists on the discharge table in the transport unit during initialization
Ex150		A plate exists on the insertion table in the transport unit during initialization
Ex151		Number of balancers is not sufficient. (The number of balancers checked by the balancer search sensor was one, two or three for both the Home and Away sides)
Ex152		Clamp arm is not in the UP position
Ex153		A fuse on the relay board was blown. (away)
Ex154		Blower is turned off, but signal does not change
Ex155		Tail clamps are missing during initialization
Ex156		The size check program of the cetering function detects that the measured plate size is longer than the expected one
Ex157		The size check program of the cetering function detects that the measured plate size is shorter than the expected one
Ex158		Both of Home and Away size check sensors are on before starting the centering program
Ex159		Auto-loader is stopped by a interlock OFF
Ex15a		The drum is rotated to “balance pin before inserted”, but status of Servo controller (SVC) is not changed to “Ready”.[away]
Ex15b		The drum is rotated to “balance pin after inserted”, but status of Servo controller (SVC) is not changed to “Ready”.[away]
Ex15d		During plate loading, double plate loading is detected
Ex15e		The loaded plate is floating from the drum is detected during drum spinning
Ex15f		The drum can not be spined up because the Away-Upper sensor of the clamp arm is off
Ex160		The drum can not be spined up because the Home-Upper sensor of the clamp arm is off
Ex161		The drum can not be spined up because the balancing pin (Away side) is not in the waiting position
Ex162		The drum can not be spined up because the balancing pin (Home side) is not in the waiting position
Ex163		The drum can not be spined up because the Upper sensor of the squeeze roller is off
Ex165		The drum is rotated to the “lead clamp position”, but the status of the Servo controller (SVC) has not changed to “Ready”
Ex166		The drum is rotated to the “tail clamp position”, but the status of the Servo controller (SVC) has not changed to “Ready”
Ex167		The drum is rotated to the “squeeze position”, but the status of the Servo controller (SVC) has not changed to “Ready”
Ex168		The drum is rotated to the “balance pin before inserted”, but the status of the Servo controller (SVC) has not changed to “Ready”
Ex169		The drum is rotated to the “balance pin after inserted”, but the status of the Servo controller (SVC) has not changed to “Ready”
Ex16a		The drum is rotated to the “pick up tail clamp position”, but the status of Servo controller (SVC) has not changed to “Ready”
Ex16b		The drum is rotated to the “plate removal position”, but the status of the Servo controller (SVC) has not changed to “Ready”
Ex16c		SVC Error has occurred during drum positioning for the lead clamp
Ex16d		SVC Error has occurred during drum positioning for the tail clamp
Ex16e		SVC Error has occurred during drum positioning for the squeeze
Ex16f		SVC Error has occurred during drum positioning for the balance pin insertion
Ex170		SVC Error has occurred during drum positioning for the balance pin pull out
Ex171		SVC Error has occurred during drum positioning for the picking up tail clamp
Ex172		SVC Error has occurred during drum positioning for the plate removal
Ex173		Time-out error has occurred during drum positioning (Lead clamp position)
Ex174		Time-out error has occurred during drum positioning (Tail clamp position)
Ex175		Time-out error has occurred during drum positioning (Squeeze position)
Ex176		Time-out error has occurred during drum positioning (Balance pin before inserted)
Ex177		Time-out error has occurred during drum positioning (Balance pin after inserted) (Home)
Ex178		Time-out error has occurred during drum positioning (Pick up tail clamp)
Ex179		Time-out error has occurred during drum positioning (Plate removal)
Ex17a		After verifying the removal of the plate, press the OK button. When the OK button is pressed, initialization begins
Ex17b		PH62A-sensor is illegal. The sensor detects a plate during initialization
Ex17c		PH25H-sensor is illegal. The sensor detects a plate during plate loading
Ex17d		Time-out error has occurred during drum positioning.(balance pin before inserted) (Away)
Ex17e		Time-out error has occurred during drum positioning.(balance pin after inserted) (Away)
Ex180		Drum does not start rotating at high-speed
Ex181		Drum does not rotate at the specified high-speed
Ex182		Error has occurred after the drum rotated at the specified high-speed
Ex183		Drum cannot be stopped when rotating at high-speed
Ex184		Drum operation is halted with an emergency stop command
Ex185		Drum operation is stopped with an abort command
Ex186		Drum’s vacuum pressure is not sufficient
Ex187		Error has occurred on the blower or the power supply of the blower is OFF
Ex188		Drum operation is halted due to low pressure in the drum
Ex189		Door is open
Ex18a		Door does not open
Ex18b		Transport tasks: Parameter error
Ex18c		Error has occured on the blower. Please turn off this machine, and turn on after waiting 10 seconds. Also, confirm whether or not the connector doesn’t come off
Ex18d		The drum can not be spun up, because some of the interlock switches are OFF, or some of the actuator’s sensors are damaged, or the blower is damaged
Ex18e		Door does not open, because some of the interlock switches are OFF (front cover or rear cover is open)
Ex190		Clamp arm does not descend (Home side)
Ex191		Clamp arm does not descend (Away side)
Ex192		Clamp arm does not ascend (Home side)
Ex193		Clamp arm does not ascend (Away side)
Ex194		When the clamp arm is lowered, the sensor (to detect whether the clamp arm pins are hooked on the clamp properly) has been turned ON (Away side)
Ex195		Trail clamp cannot be locked (Home side)
Ex196		Trail clamp cannot be locked (Away side)
Ex197		Trail clamp cannot be unlocked (Home side)
Ex198		Trail clamp cannot be unlocked (Away side)
Ex199		Balancer drive pin cannot be inserted (Home side)
Ex19a		Balancer drive pin cannot be inserted (Away side)
Ex19b		Balancer drive pin cannot be pulled out (Home side)
Ex19c		Balancer drive pin cannot be pulled out (Away side)
Ex19d		Balancer pin cannot be detected before insertion (Away side)
Ex19e		Balancer pin cannot be detected before pull out (the balancer is not moving) (Away side)
Ex19f		No balancer has been detected by the balancer search sensor (Home side)
Ex1a0		No balancer has been detected by the balancer search sensor (Away side)
Ex1a1		Number of balancers is not sufficient. (Home side)
Ex1a2		Number of balancers is not sufficient. (Away side)
Ex1a3		Rear cover is open (Some interlock switch are OFF)
Ex1a4		Away side cover is open (Some interlock switch are OFF)
Ex1a5		Front cover is open (Some interlock switch are OFF)
Ex1a6		A plate cannot be carried into the transport unit
Ex1a7		A plate cannot be carried to sensor PPH50-2
Ex1a8		Auto-loader is not turned on, or some interlock switches on Auto-loader are OFF
Ex1a9		Cassete carrier was removed
Ex1aa		The door of the cassette part is open
Ex1ab		Rear-cover of Auto-loader was opend
Ex1ac		Top cover was opened
Ex1ad		A slipping paper under a plate was detected. Or a plate size (in the Y direction) is shorter than the set value
Ex1ae		A slipping paper on a plate was detected. Or a plate size (in the Y direction) is shorter than the set value
Ex1b0		Time-out error has occurred when Punch 1 is activated
Ex1b1		Time-out error has occurred when Punch 2 is activated
Ex1b2		Time-out error has occurred when Punch 3 is activated
Ex1b3		Time-out error has occurred when Punch 4 is activated
Ex1b4		Time-out error has occurred when Punch 5 is activated
Ex1b5		Time-out error has occurred when Punch 6 is activated
Ex1b6		Time-out error has occurred when Punch 7 is activated
Ex1b7		Time-out error has occurred when Punch 8 is activated
Ex1b8		Time-out error has occurred when Punch 9 is activated
Ex1b9		Time-out error has occurred when Punch A is activated
Ex1ba		Time-out error has occurred when Punch B is activated
Ex1bb		Time-out error has occurred when Punch C is activated
Ex1bc		Nip roller(Unload) does not ascend
Ex1bd		Nip roller(Unload) does not descend
Ex1be		Unload path does not ascend
Ex1bf		Unload path does not descend
Ex1c0		Time-out error has occurred when the caterpillar motor is activated
Ex1c1		Error has occurred on the caterpillar motor (while the alignment plate is finely returning to its origin)
Ex1c2		Door does not open
Ex1c3		Door does not close
Ex1c7		Plate is not transferred to the punch unit [PH59]
Ex1c8		After a plate is transferred to the gripper clamp, the plate detection sensor (PH25H/A) does not switch to ON [PH59]
Ex1c9		When the transport unit descends, plate cannot be transferred into the transport unit
Ex1ca		When the plate is unloaded, PH53-sensor does not switch to ON
Ex1cb		Opened shutter obstructs trans path driving
Ex1cc		Trail clamp arm obstructs trans path driving
Ex1cd		A plate remains in a machine
Ex1d0		Transfer operation is halted with an abort command
Ex1d1		Transport tasks are being processed
Ex1d2		Transport tasks are not being processed
Ex1d3		Transport tasks: Message order error
Ex1d4		Transport system is not initialized
Ex1e0		SVC User constant breakdown
Ex1e1		SVC User constant setting error
Ex1e2		SVC over-current
Ex1e3		SVC detection of regenerative error
Ex1e4		SVC postion error pulse overflow
Ex1e5		SVC Main circuit voltage error detection
Ex1e6		SVC over speed
Ex1e7		SVC overloaded (high load)
Ex1e8		SVC overloaded (low load)
Ex1e9		SVC stauts 99h
Ex1ea		SVC heat sink has overheated
Ex1eb		SVC stauts b1h
Ex1ec		SVC is out of control
Ex1ed		SVC phase error has been detected in the encoder
Ex1ef		SVC A and B phase for the encoder has broke down
Ex1f0		SVC C phase for the encoder has broke down
Ex1f1		SVC Power line Open phase
Ex1f3		SVC An instantaneous loss of power has occurred
Ex1f4		SVC unknown error
Ex1f5		Detection of servo encorder error
Ex200		Exposure operation is interrupted with an abort command
Ex201		Exposure processing task is now processing another command
Ex202		Cancellation requested while processing was not being performed
Ex203		PGON is not asserted
Ex204		START signal is not asserted
Ex205		START signal is not negated
Ex206		Test pattern; Data is not transferred
Ex207		Test pattern; Data transfer is not completed
Ex208		Reset procedure for TB64 board is not completed
Ex209		The set value for the drum rotation speed is too large
Ex20a		No plate edge is detected (when the plate edge sensor moves to the Away side)
Ex20b		No plate edge is detected (when the plate edge sensor is returning to the Home side)
Ex20c		Recording head has traveled beyond the limit (on the Away side)
Ex20d		Recording head has traveled beyond the limit (on the Home side)
Ex20e		Recording head positioning range error
Ex20f		Recording head has not been positioned at its origin. (Origin sensor does not turn OFF)
Ex210		Recording head has not been positioned at its origin. (Origin sensor does not turn ON)
Ex211		Emergency stop is requested for the secondary-scanning motor
Ex212		Secondary-scanning motor is deactivated with an abort command
Ex213		Secondary scanning motor is illegal
Ex214		Exposure in the secondary scanning direction exceeds the effective image ouput range
Ex215		FPGA sequence error
Ex216		Time-out error has occurred when the secondary scanning motor is activated
Ex217		EZ search has not detected the ORG sensor
Ex218		EZ search has not detected the EZ sensor
Ex219		When the CAL sensor search was executed, the maximum light intensity was less than 50 mW
Ex21a		When the CAL sensor search was executed, the light intensity at the measurement starting point was the maximum
Ex21b		When the CAL sensor search was executed, the light intensity at the measurement end point was the maximum
Ex21c		CAL sensor search has not detected the over travel limit switch on the recording head’s Home side
Ex21d		Test pattern parameter error
Ex21e		PGON signal is not negated
Ex21f		Secorndary direction origin point setup procedure failure (The calibrated origin point is not the same as logical origin point)
Ex220		After an image data transfer from RIP is interrupted, it isn’t resumed
Ex221		Cooling fan for TB64 board is illegal
Ex222		Hungup was detected
Ex223		The version of TB64 board and FES board is inharmonious
Ex224		Machine and firmware is inharmonious
Ex300		Both of plate pad and paper pad are not in original point
Ex301		After a slipping paper is removed, plate cannot be detected
Ex302		A slipping paper on a plate was detected. Or a plate size (in the Y direction) is shorter than the set value
Ex303		Plate pad cannot be initialized
Ex304		Plate pad cannot carry a plate
Ex305		During the carring a plate, plate pad dropped the plate
Ex306		Paper pad cannot be initialized
Ex307		Air pressure in the plate pad does not go down
Ex308		Air pressure in the paper pad does not go down
Ex309		Time-out error has occurred when plate pad was moved
Ex30a		Time-out error has occurred when paper pad was moved
Ex30b		Time-out error has occurred when plate pad was moved intermittently
Ex30c		Time-out error has occurred when paper pad was moved intermittently
Ex30e		During the removing a papaer, PH90 does not switch to ON
Ex30f		During the removing a papaer, PH90 does not switch to OFF
Ex310		Rear cover of auto-loader is open
Ex311		Top cover of auto-loader is open
Ex312		Cassette carrier is not set
Ex313		A plate remains in the bridge unit
Ex314		An interleaf remains in the paper exit
Ex315		Nip roller does not ascend or some interlock switch are illegal, or emergency switch is turned ON
Ex316		Nip roller does not descend
Ex317		Auto-loader is not turned on, or all interlock switch are OFF
Ex318		A plate cannot be carried to the bridge-passing sensor
Ex319		The plate pad went down from the original point
Ex31a		The paper pad went down from the original point
Ex31b		Rear-cover of Auto-loader was opened
Ex31c		Top cover was opened
Ex31d		Door was opened
Ex31e		Cassete carrier was removed
Ex31f		During the carring a paper, paper pad dropped the paper
Ex320		Plate pad dropped a plate before the plate pad reached the intermediate sensor
Ex321		A slipping paper on front of a plate was detected
Ex322		A slipping paper under front of a plate was detected
Ex323		Intermediate sensor is OFF
Ex324		Power switch was turned off while Auto-loader was moving
Ex325		A plate cannot be carried to the intermediate sensor
Ex326		A slipping paper under a plate was detected. Or a plate size (in the Y direction) is shorter than the set value
Ex327		The bridge-passing sensor does not turn OFF (for Jig mode)
Ex328		Door is open
Ex32c		The nip-roller for paper discharge cann’t be opened
Ex340		Door is open
Ex341		The interlock switch-3 is OFF
Ex342		The interlock switch-2 is OFF
Ex343		The interlock switch-1 is OFF
Ex344		A fuse on the relay board at home side has blown
Ex345		A fuse on the relay board at away side has blown
Ex346		Nip roller does not descend
Ex347		Nip roller does not ascend
Ex348		Shutter does not open
Ex349		Shutter does not close
Ex380		The door of the cassette part is open
Ex381		Time-out error has occurred when lift was initialized
Ex382		Time-out error has occurred when lift was moved
Ex383		Though the lift was initialized, the origin sensor is not ON
Ex384		The lift is not in the position where it is specified
Ex385		Already, there has been a cassette on the lift
Ex386		There are some cassettes which aren’t being set properly
Ex387		MA-L can’t be initialized because some cassettes are not in the lift or the cassette properly
Ex388		There is no cassette in the specified cassette slot
Ex389		There is no cassette on the lift
Ex38a		Lift has traveled beyond the limit (on the Up side)
Ex38b		Lift has traveled beyond the limit (on the Down side)
Ex38d		A cassette is already in the place to return a cassette
Ex38e		A lift can’t be raised and lowered because some cassettes are not in the lift or the cassette properly
Ex38f		Time-out error has occurred when a cassette was moved to cassette part
Ex390		Time-out error has occurred when a cassette was moved to lift
Ex391		Either plate pad or paper pad is not in original point
Ex392		An ineffective cassette number was indicated
Ex393		Cassette has traveled beyond the limit (on the Lift side)
Ex394		Cassette has traveled beyond the limit (on the Cassette side)
Ex395		MA-L can’t be initialized because some cassettes can’t be returned to the origin
Ex396		Though there is a cassette on the lift, the place to return the cassette isn’t vacant
Ex397		Though the movement of the lift was finished, the lift position sensor at the target position is not on
Ex398		MA-L Servo alarm
Ex399		The belt broke
Ex400		Plate has already been loaded
Ex401		Plate has not been loaded
Ex402		Door is open
Ex403		Dump interleaves from the collection box
Ex600		Either the conveyor, processor, or stocker is not turned on, or is in the busy status or error status
Ex601		Either the conveyor, processor, or stocker is not turned on, or is in the busy status or error status
Ex602		The plate cannot be transferred into the AT unit
Ex603		The plate cannot be transferred completely into the AT unit
Ex606		Error
Ex607		Busy
Ex608		Error
Ex609		Busy
Ex60a		Error
Ex60b		Busy
Ex60c		Error occurred in ATM while a plate was carried to ATM
Ex60d		When the plate is unloaded, the plate pass sensor (PH70) does not switch to ON
Ex80d		The result of the calculation “Initial value + increment value * (repetition – 1)” exceeds the upper limit value
Ex80e		(The result of the calculation “Exposure starting point + (pattern width + gap) * (repetition – 1)” exceeds the plate size
Ex80f		The specified plate is not linked with the printing-machine’s data
Ex810		Perform initialization at the service screen
Ex811		No plate is set at inlet of transport unit
Ex812		Plate (printer) size specified by the host computer is not registered
Ex813		Image size specified by host computer is larger than allowable output image size
Ex814		Current offset of printing machine settings cause image to extend off plate
Ex815		Current paper-position of printing machine settings cause image to extend outside of allowable exposure area
Ex817		Some LD is nearing the end of its usable life
Ex818		There are some punch blocks, which have been used for more than the endurance time
Ex81a		It failed to read the cassette number. It considers that the cassette number is No.1
Ex81b		Some LD’s cannot be calibrated to the target power
Ex81c		Some LD’s cannot be calibrated to the target power
Ex81d		Some LD’s cannot be calibrated to target power
Ex81e		The temperature of the environment is greater than 28degrees
Ex81f		The temperature of the environment is less than 18degrees
Ex820		Sensor for the temperature of the environment has not been connected
Ex821		Trail clamps are nearing the end of its usable life
Ex822		Trail clamps have been used for more than the endurance time
Ex823		Backup/restore of the data on NVRAM can’t be performed, because the Dip-Sw 2 is not on
Ex824		The backup of the data on NVRAM is not in Flash-Memory
Ex825		Calibration must be done because there is some LD which doesn’t reach the target power. But, LD calibration can not processed because temperature of LD block is too low
Ex826		The direction where a connected conveyer can’t be changed is set up in the plate types setting
Ex827		No response was returned from the conveyor
Ex828		An error was returned from the conveyer toward the switching command
Ex829		The conveyer can’t be changed to the direction that is set up in the plate types setting
Ex82a		Since the light intensity of laser diodes is detected as having deviated more than +-5% from the specified value, the equipment executes the calibration
Ex82b		The head task was hanged up.
Ex82c		Head:Iopd data error
Ex850		Communication with the RAS server was interrupted. (RAS server was turned off or RS-232C cable was drawn out)
Ex851		No response come from DNS
Ex852		Communication with the RAS server has resume
Ex853		It failed in the connection to the rotating light server
Ex854		The name of the mail server isn’t right
Ex855		It failed in the connection to the mail server
Ex856		Mail account was rejected
Ex857		An error occurred in the transmission of DATA command
Ex858		An error occurred in the transmission of header
Ex859		An error occurred in the transmission of body
Ex85a		An error occurred in the transmission of attached file
Ex85b		An error occurred in the transmission of TO command
Ex85c		A command was sent to the SMTP server. But, no answer was returned from the server
Ex880		Servo pack: Time-out error occurred while receiving data
Ex881		Servo-Pack:Address error
Ex882		Servo-Pack:Data error
Ex883		Servo-Pack:Check sum error
Ex884		Servo-Pack:Undefined error code
Ex885		Servo-Pack:Number of received characters are insufficient
Exd01		Excessive current in the LD drive (driver 1 board)
Exd02		Excessive current in the LD drive (driver 2 board)
Exd03		Excessive current in the LD drive (driver 3 board)
Exd04		Excessive current in the LD drive (driver 4 board)
Exd05		Driver board temperature error
Exd08		Irregular peltier
Exd09		Irregular FES board power supply
Exd0a		Irregular +9 V power supply
Exd21		Temperature at the RH base > 35degrees (Temperature of environment > 28degrees)
Exd22		Temperature at the periphery of the optical unit is high
Exd25		Sensor for the RH base has not been connected
Exd28		Temperature of the LD block is low
Exd30		Writing error occurred when the recording head received the AC command
Exd31		Writing error on EEPROM
Exd32		Data error due to a divide-by-zero error
Exd33		Calibration must be done
Exd40		Temperature of the LD block is high. block 0
Exd41		Temperature of the LD block is high. block 1
Exd42		Temperature of the LD block is high. block 2
Exd43		Temperature of the LD block is high. block 3
Exd44		Temperature of the LD block is high. block 4
Exd45		Temperature of the LD block is high. block 5
Exd46		Temperature of the LD block is high. block 6
Exd47		Temperature of the LD block is high. block 7
Exd48		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees.) block 0
Exd49		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees.) block 1
Exd4a		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees.) block 2
Exd4b		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees.) block 3
Exd4c		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature ofenvironment ≤ 28degrees.) block 4
Exd4d		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees.) block 5
Exd4e		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees.) block 6
Exd4f		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees.) block 7
Exd50		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment > 28degrees.) block 0
Exd51		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment > 28degrees.) block 1
Exd52		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment > 28degrees.) block 2
Exd53		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment > 28degrees.) block 3
Exd54		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment > 28degrees.) block 4
Exd55		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment > 28degrees.) block 5
Exd56		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment > 28degrees.) block 6
Exd57		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment > 28degrees.) block 7
Exd58		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment ≤ 28degrees.) block 0
Exd59		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment ≤ 28degrees.) block 1
Exd5a		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment ≤ 28degrees.) block 2
Exd5b		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment ≤ 28degrees.) block 3
Exd5c		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment ≤ 28degrees.) block 4
Exd5d		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment ≤ 28degrees.) block 5
Exd5e		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment ≤ 28degrees.) block 6
Exd5f		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment ≤ 28degrees.) block 7
Exd60		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment > 28degrees.) block 0
Exd61		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment > 28degrees.) block 1
Exd62		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment > 28degrees.) block 2
Exd63		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment > 28degrees.) block 3
Exd64		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment > 28degrees.) block 4
Exd65		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment > 28degrees.) block 5
Exd66		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment > 28degrees.) block 6
Exd67		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment > 28degrees.) block 7
Exd68		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees.) block 0
Exd69		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees.) block 1
Exd6a		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees.) block 2
Exd6b		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees.) block 3
Exd6c		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees.) block 4
Exd6d		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees.) block 5
Exd6e		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees.) block 6
Exd6f		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees.) block 7
Exd70		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit ≤ 35degrees.) block 0
Exd71		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit ≤ 35degrees.) block 1
Exd72		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit ≤ 35degrees.) block 2
Exd73		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit ≤ 35degrees.) block 3
Exd74		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit ≤ 35degrees.) block 4
Exd75		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit ≤ 35degrees.) block 5
Exd76		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit ≤ 35degrees.) block 6
Exd77		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit ≤ 35degrees.) block 7
Exd78		Dew condensation error. block 0
Exd79		Dew condensation error. block 1
Exd7a		Dew condensation error. block 2
Exd7b		Dew condensation error. block 3
Exd7c		Dew condensation error. block 4
Exd7d		Dew condensation error. block 5
Exd7e		Dew condensation error. block 6
Exd7f		Dew condensation error. block 7
Exd80		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine ≥ 18degrees.) block 0
Exd81		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine ≥ 18degrees.) block 1
Exd82		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine ≥ 18degrees.) block 2
Exd83		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine ≥ 18degrees.) block 3
Exd84		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine ≥ 18degrees.) block 4
Exd85		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine ≥ 18degrees.) block 5
Exd86		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine ≥ 18degrees.) block 6
Exd87		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine ≥ 18degrees.) block 7
Exd88		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine < 18degrees.) block 0
Exd89		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine < 18degrees.) block 1
Exd8a		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine < 18degrees.) block 2
Exd8b		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine < 18degrees.) block 3
Exd8c		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine < 18degrees.) block 4
Exd8d		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine < 18degrees.) block 5
Exd8e		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine < 18degrees.) block 6
Exd8f		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine < 18degrees.) block 7
Exd90		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit ≥ 17degrees.) block 0
Exd91		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit ≥ 17degrees.) block 1
Exd92		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit ≥ 17degrees.) block 2
Exd93		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit ≥ 17degrees.) block 3
Exd94		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit ≥ 17degrees.) block 4
Exd95		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit ≥ 17degrees.) block 5
Exd96		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit ≥ 17degrees.) block 6
Exd97		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit ≥ 17degrees.) block 7
Exd98		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment ≥ 18degrees.) block 0
Exd99		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment ≥ 18degrees.) block 1
Exd9a		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment ≥ 18degrees.) block 2
Exd9b		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment ≥ 18degrees.) block 3
Exd9c		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment ≥ 18degrees.) block 4
Exd9d		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment ≥ 18degrees.) block 5
Exd9e		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment ≥ 18degrees.) block 6
Exd9f		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment ≥ 18degrees.) block 7
Exda0		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment < 18degrees.) block 0
Exda1		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment < 18degrees.) block 1
Exda2		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment < 18degrees.) block 2
Exda3		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment < 18degrees.) block 3
Exda4		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment < 18degrees.) block 4
Exda5		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment < 18degrees.) block 5
Exda6		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment < 18degrees.) block 6
Exda7		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment < 18degrees.) block 7
Exdb0		LD block can not cool. block 0
Exdb1		LD block can not cool. block 1
Exdb2		LD block can not cool. block 2
Exdb3		LD block can not cool. block 3
Exdb4		LD block can not cool. block 4
Exdb5		LD block can not cool. block 5
Exdb6		LD block can not cool. block 6
Exdb7		LD block can not cool. block 7
Exdb8		LD block can not cool. block 0
Exdb9		LD block can not cool. block 1
Exdba		LD block can not cool. block 2
Exdbb		LD block can not cool. block 3
Exdbc		LD block can not cool. block 4
Exdbd		LD block can not cool. block 5
Exdbe		LD block can not cool. block 6
Exdbf		LD block can not cool. block 7
Exdc0		Irregular peltier. block 0
Exdc1		Irregular peltier. block 1
Exdc2		Irregular peltier. block 2
Exdc3		Irregular peltier. block 3
Exdc4		Irregular peltier. block 4
Exdc5		Irregular peltier. block 5
Exdc6		Irregular peltier. block 6
Exdc7		Irregular peltier. block 7
Exdd0		TP1-TP3 peltier line is incorrect
Exdd1		TP1-TP5 peltier line is incorrect
Exdd2		TP1-TP7 peltier line is incorrect
Exdd3		TP3-TP5 peltier line is incorrect
Exdd4		TP3-TP7 peltier line is incorrect
Exdd5		TP5-TP7 peltier line is incorrect
Exdd6		TP2-TP4 peltier line is incorrect
Exdd7		TP2-TP6 peltier line is incorrect
Exdd8		TP2-TP8 peltier line is incorrect
Exdd9		TP4-TP6 peltier line is incorrect
Exdda		TP4-TP8 peltier line is incorrect
Exddb		TP6-TP8 peltier line is incorrect
Exe01		Excessive current in the LD drive (driver 1 board)
Exe02		Excessive current in the LD drive (driver 2 board)
Exe03		Excessive current in the LD drive (driver 3 board)
Exe04		Excessive current in the LD drive (driver 4 board)
Exe05		Driver board temperature error or FPGA Version error
Exe06		-5 V power supply error
Exe07		Calibration sensor is not connected
Exe08		Offset error in the calibration sensor
Exe09		Irregular 5 V power supply
Exe0a		Irregular +15 V power supply
Exe0b		Irregular -15 V power supply
Exe0c		Irregular 24 V power supply
Exe0d		Cover switch is OFF
Exe0e		BL command error (counter value is 0)
Exe0f		Zoom sensor does not detect
Exe10		Focus sensor does not detect
Exe11		Time over for home return.(zoom or focus motor)
Exe12		Power supply irregular while the motor is driving.(zoom or focus motor)
Exe13		[8600 ]Pulse motor has traveled beyond the away limit. (zoom or focus motor)
Exe13		[8000-2]Pulse motor has traveled beyond the limit. (zoom or focus motor)
Exe14		[8600 ]Pulse motor has traveled beyond the home limit. (zoom or focus motor)
Exe14		[8600-2]Irregular power supply(instantaneous loss)
Exe20		Temperature of the LD block is high
Exe21		Temperature at the periphery of the optical unit is high
Exe22		Temperature of the radiating fin of the Peltier element is high
Exe23		Dew condensation error
Exe24		Sensor for LD block has not been connected
Exe25		Sensor for the periphery of the optical unit has not been connected
Exe26		Sensor for the radiating fin of the Peltier element has not been connected
Exe27		Sensor for the dew condensation detection sensor has not been connected
Exe28		Temperature of the LD block is low
Exe30		Power supply error occurred when the recording head received the DW command
Exe31		Command error occurred when the recording head received the DW command
Exe32		Download error occurred when the recording head received the DP command
Exe33		Download error occurred when the recording head received the DF command
Exe34		Download address error occurred
Exe35		Error occurred when the recording head received the BU command
Exe36		Error occurred when the recording head received the BD command
Exe40		Writing error occurred when the recording head received the AC command
Exe41		Writing error on EEPROM
Exe42		RAM error
Exe43		ROM check sum error
Exe44		FPGA error
Exe45		Data error due to a divide-by-zero error
Exe60		LD Current setting error
Exe61		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature environment ≤ 28degrees)
Exe62		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment > 28degrees)
Exe63		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment ≤ 28degrees)
Exe64		Temperature at the periphery of the optical unit > 35degrees (Temperature of environment ≤ 28degrees)
Exe65		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees)
Exe66		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit ≤ 35degrees)
Exe67		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine ≥ 18degrees)
Exe68		The LD block has dew (Temperature of the LD block < 22degrees. Temperature inside the machine < 18degrees)
Exe69		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit ≥ 17degrees)
Exe6a		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment ≥ 18degrees)
Exe6b		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees)
Exe6c		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment > 28degrees)
Exe6d		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit ≤ 35degrees. Temperature of environment ≤ 28degrees)
Exe6e		Temperature at the periphery of the optical unit > 35degrees (Temperature of environment ≤ 28degrees)
Exe6f		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment ≤ 28degrees)
Exe70		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit ≤ 35degrees)
Exe71		It is just before an exposure head has dew (Temperature of the LD block < 22degrees. Temperature of environment ≥ 18 degrees)
Exe72		It is just before an exposure head has dew (Temperature of the LD block < 22degrees. Temperature of environment < 18 degrees)
Exe73		5degrees ≤ Temperature of the LD block < 17degrees (Temperature of environment ≥ 18degrees)
Exe74		5degrees ≤ Temperature of the LD block < 17degrees (Temperature of environment < 18degrees)
Exea0		Light intensity adjustment error 0ch
Exea1		Light intensity adjustment error 1ch
Exea2		Light intensity adjustment error 2ch
Exea3		Light intensity adjustment error 3ch
Exea4		Light intensity adjustment error 4ch
Exea5		Light intensity adjustment error 5ch
Exea6		Light intensity adjustment error 6ch
Exea7		Light intensity adjustment error 7ch
Exea8		Light intensity adjustment error 8ch
Exea9		Light intensity adjustment error 9ch
Exeaa		Light intensity adjustment error 10ch
Exeab		Light intensity adjustment error 11ch
Exeac		Light intensity adjustment error 12ch
Exead		Light intensity adjustment error 13ch
Exeae		Light intensity adjustment error 14ch
Exeaf		Light intensity adjustment error 15ch
Exeb0		Light intensity adjustment error 16ch
Exeb1		Light intensity adjustment error 17ch
Exeb2		Light intensity adjustment error 18ch
Exeb3		Light intensity adjustment error 19ch
Exeb4		Light intensity adjustment error 20ch
Exeb5		Light intensity adjustment error 21ch
Exeb6		Light intensity adjustment error 22ch
Exeb7		Light intensity adjustment error 23ch
Exeb8		Light intensity adjustment error 24ch
Exeb9		Light intensity adjustment error 25ch
Exeba		Light intensity adjustment error 26ch
Exebb		Light intensity adjustment error 27ch
Exebc		Light intensity adjustment error 28ch
Exebd		Light intensity adjustment error 29ch
Exebe		Light intensity adjustment error 30ch
Exebf		Light intensity adjustment error 31ch
Exec0		Light intensity adjustment error 32ch
Exec1		Light intensity adjustment error 33ch
Exec2		Light intensity adjustment error 34ch
Exec3		Light intensity adjustment error 35ch
Exec4		Light intensity adjustment error 36ch
Exec5		Light intensity adjustment error 37ch
Exec6		Light intensity adjustment error 38ch
Exec7		Light intensity adjustment error 39ch
Exec8		Light intensity adjustment error 40ch
Exec9		Light intensity adjustment error 41ch
Execa		Light intensity adjustment error 42ch
Execb		Light intensity adjustment error 43ch
Execc		Light intensity adjustment error 44ch
Execd		Light intensity adjustment error 45ch
Exece		Light intensity adjustment error 46ch
Execf		Light intensity adjustment error 47ch
Exed0		Light intensity adjustment error 48ch
Exed1		Light intensity adjustment error 49ch
Exed2		Light intensity adjustment error 50ch
Exed3		Light intensity adjustment error 51ch
Exed4		Light intensity adjustment error 52ch
Exed5		Light intensity adjustment error 53ch
Exed6		Light intensity adjustment error 54ch
Exed7		Light intensity adjustment error 55ch
Exed8		Light intensity adjustment error 56ch
Exed9		Light intensity adjustment error 57ch
Exeda		Light intensity adjustment error 58ch
Exedb		Light intensity adjustment error 59ch
Exedc		Light intensity adjustment error 60ch
Exedd		Light intensity adjustment error 61ch
Exede		Light intensity adjustment error 62ch
Exedf		Light intensity adjustment error 63ch
Exee0		Incorrect command has been input
Exee1		Temperature of the LD block > 28degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment > 28degrees)
Exee2		Temperature at the periphery of the optical unit > 35degrees (Temperature of environment > 28degrees)
Exee3		Temperature of the radiator > 55degrees (Temperature at the periphery of the optical unit > 35degrees. Temperature of environment > 28degrees)
Exee4		It is just before an exposure head has dew (Temperature of the LD block ≥ 22degrees.)
Exee5		Temperature of the LD block < 5degrees (Temperature at the periphery of the optical unit < 17degrees. Temperature of environment < 18degrees.)
Exef0		Recording head processing task is now processing another message
Exef2		Recording head unit is not running
Exef3		Check sum error occurred when data was uploaded
Exef4		Address error occurred when data was uploaded
Exef5		LD calibration can not processed because temperature of LD block is too low
Exef6		A command was sent to the exposure head. But, no answer was returned from the exposure head
Exfa0		System error (stack overflow)
Exfa1		Floating point arithmetic error
Exfa2		Divide-by-zero error
Exfa3		System error (semaphore)
Exfb0		Flash memory erase error
Exfb1		Flash memory erase error (during verification)
Exfb2		Flash memory write error
Exfb3		Incompatible flash memory

Heidelberg ProSetter

Topsetter 74 / Acento II / Screen PT-R4xxx

Topsetter 102 screen pt r8xxx

Machine Error Codes

Contact Us