07814 652568 steve@rsprepress.com

Linotronic 300R

Computer to FIlm, error codes

 Boot Status Messages
 Code:                 Description:
 200    Selftest 0 
 201    Selftest 1
 202    Selftest 2
 203    Selftest 3
 204    Selftest 4
 205    Selftest 5 
 206    Selftest 6
 207    Selftest 7
 208    Selftest 8
 210    Selftest done

 

 
 Recorder Messages
 Error Code:      Description:
 001    Film End
 002    No take up cassette
 003    Take up cassette full
 004    Caution: Tako malfunction
 005    Cutter not home
 006    Density malfunction
 007    OLP-FLAG too long
 010    Exposure active
 011    Exposure ready
 012    Exposure stopped
 013    Test exposure ready
 014    Text exposure ready
 020    Film load active
 021    Film load ready
 022    Take up cassette fitted
 023    Insert film
 024    Adjust film
 025    Film in transport
 026    Film load stopped
 030    Film unload active
 031    Film unload active
 032    Take up casette is fitted
 040    Film advance active
 041    Film advance ready
 050    Cut active
 051    Cut ready
 052    Cut stopped
 100    Caution: Polygon error
 101    Abort: Fine density error
 102    Abort: Coarse density error
 103    Abort: Density adjust
 104    Film start / stop. No start
 105    Film start / stop inactive
 110    Abort: Fatal error BELI
 111    Abort: Command error
 112    Abort: Data error BELI
 113    Abort: X/Y error
 116    Abort: Machine parameter
 120    Abort: Film load command error
 121    Abort: Film shutter does not close
 122    Abort: Film Tension
 141    Abort: Film unload command error
 150    Abort: Cutter does not move
 151    Abort: Cutter is blocked
 160    Abort: No input processor Clk
 161    Abort: No output process Clk
 162    Abort: Input window counter
 163    Abort: Output window counter
 164    Abort: Altern buffer A counter
 165    Abort: Altern buffer A data
 166    Abort: Altern buffer B counter
 167    Abort: Altern buffer B data
 180    Abort: Bus error
 181    Abort: Address error
 182    Abort: Ilegal instruction
 183    Abort: Zero divide
 184    Abort: CHK instruction
 185    Abort: TRAPV instruction
 186    Abort: Privilege violation
 187    Abort: Trace
 188    Abort: Reserved
 189    Abort: Trap
 190    Abort: Auto vector interrupt
 191    Abort: Hardware vector interupt
 215    Message: Adjust active
 216    Message: Adjust ready
 217    Message: Exposure active
 218    Message: Exposure ready
 219    Message: Density adjust active
 220    Message: Density adjust ready
 221    Message: Tako adjust active
 222    Message: Tako adjust ready
 233    O.L.P. error. No take up cassette
 235    Sender not active
 236    SOPR inactive
 237    SSCN exceeds active length
 238    Timeout LI2
 240    LI5 not available
 246    EEprom error Write
 248    EEprom error Data
 252    EEprom error Block
 254    NV ram error (LT50)
 

Heidelberg Herkules

Computer to FIlm, error codes

Error Index:
 0000-9FFF: Errors    0000-00FF: reserve
     0100-08FF: boot system
     0800-0FFF: main control
     1000-1FFF: communication control
     2000-2FFF: video control
     3000-3FFF: Material control
     4000-4FFF: feed control
     5000-5FFF: user interface
     6000-6FFF: machine drivers
     7000-77FF: operating system PSOS-Fehler
     7800-7BFF: file system
     7C00-7DFF: laser control HELIOS
     7E00-7FFF: peeler control HELIOS
     8000-87FF: ecc control
     8800-9FFF: reserve (free)
 A000-BFFF: Warnings    A000-A1FF: boot system
     A200-A3FF: main control
     A400-A5FF: communication control
     A600-A7FF: video control
     A800-A9FF: Material control
     AA00-ABFF: feed control
     AC00-ADFF: user interface
     AE00-AFFF: machine driver
     B000-B1FF: operation system PSOS+
     B200-B3FF: file system
     B400-B5FF: ecc control
     B600-BFFF: reserve (free)
 C000-DFFF: User Info    C000-C3FF: user intervention for STA
     C400-C7FF: user intervention for ORL
     C800-CBFF: user intervention for SWE
     CC00-CFFF: user intervention for HAU
     C400-C7FF: user intervention for ORL
     D400-DFFF: reserve (free)
 E000-FFFE: reserve    
 FFFF: special used    FFFF     : special used by HERKULES
 
Error:                                     Description:
 USER INFO 0000    Recorder is ready for operating
 ERROR 0001    Recorder in test run – No exposure possible
 ERROR 0800    Recorder hardware defective
 ERROR 0801    The inserted diskette is not the system diskette for this recorder
 ERROR 0802    The graphics display could not be initialized
 ERROR 0803    The material reception unit (collecting cassette or on-line device connected) has not been selected
 ERROR 0804    Supply cassette not inserted
 ERROR 0805    Collecting cassette not inserted
 ERROR 0806    Material feed error
 ERROR 0807    Collecting cassette has not been emptied
 ERROR 0808    Material feed into the material reception unit (collecting cassette or connected on-line device) not  possible 
 ERROR 0809    An error occurred in the recorder cutting device
 ERROR 080A    Supply cassette is empty
 ERROR 080D    Internal error
 ERROR 080E    An error occurred during the automatic material position and width recognition
 ERROR 080F    The on-line processor is not switched on
 ERROR 0810    On-line processor not ready
 ERROR 0811    The on-line processor is not connected to the on-line recorder interface
 ERROR 0812    Power supply error – An error occurred in the negative 12 Volt power supply;
 ERROR 0813    Power supply error – An error occurred in the positive 12 Volt power supply
 ERROR 0814    Power supply error – An error occurred in the negative 15 Volt power supply
 ERROR 0815    Power supply error – An error occurred in the positive 15 Volt power supply
 ERROR 0816    Power supply error – An error occurred in the first negative 2 Volt power supply
 ERROR 0817    Power supply error – An error occurred in the negative 5.2 Volt power supply
 ERROR 0818    Power supply error – An error occurred in the positive 7.5 Volt power supply
 ERROR 0819    Power supply error – An error occurred in the positive 24 Volt power supply
 ERROR 081A    Power supply error – An error occurred in the second negative 2 Volt power supply
 ERROR 081B    Power supply error – An error occurred in the positive 28 Volt power supply
 ERROR 081C    Power supply error – An error occurred in one of the power supply modules
 ERROR 081D    The recorder could not be initialized
 ERROR 081F    The supply cassette does not belong to this recorder
 ERROR 0900    The communication with the laser unit is interrupted
 ERROR 1001    No more memory available to create a SPEEDWAY message
 ERROR 2000    The recorder hardware could not be reset
 ERROR 2001    The recorder hardware could not be initialized
 ERROR 2002    The recorder hardware could not be reset
 ERROR 2003    The recorder hardware could not be initialized
 ERROR 2004    The recorder hardware could not be initialized
 ERROR 2005    The recorder hardware could not be initialized
 ERROR 2007    The recorder hardware could not be initialized
 ERROR 2008    The SPEEDWAY link is interrupted
 ERROR 2009    The SPEEDWAY link is interrupted
 ERROR 200A    The SPEEDWAY link is interrupted
 ERROR 200B    The system memory for SPEEDWAY communication could not be released
 ERROR 200C    An error occurred in the program sequence
 ERROR 3101    An internal error occurred when calling up the material control
 ERROR 3102    An internal error occurred when calling up the material control
 ERROR 3103    An internal error occurred when calling up the material control
 ERROR 3104    An internal error occurred when calling up the material control
 ERROR 3105    An internal error occurred when calling up the material control
 ERROR 3106    The material feed length exceeds the maximum feed length
 ERROR 3107    The material type, which is selected in the material parameter MATERIAL_TYPE, isn’t supported by the recorder
 ERROR 3108    The material thickness (in combination with the selected material type) isn’t supported by the recorder. The thickness is selected in the material parameter MATERIAL_THICKNESS
 ERROR 3109    The measured material width (in combination with the selected material thickness and material type) isn’t supported by the recorder
 ERROR 3110    The VAR_MAT_CONTROL-parameters (PID 681-700) in the static parameters do not have the defined format or they are corrupted
 ERROR 3200    An error occurred when initializing the punch
 ERROR 3201    An error occurred when selecting the punches
 ERROR 3202    An error occurred during the punching
 ERROR 3300    An error occurred during the transport of the residual material – The supply cassette is empty
 ERROR 3301    An error occurred during the transport of the residual material – The supply cassette is empty
 ERROR 3302    An error occurred during the transport of the residual material – The supply cassette is empty
 ERROR 3400    The residual material measurement is incorrect
 ERROR 3401    The residual material measurement is incorrect
 ERROR 3402    The residual material measurement is incorrect
 ERROR 3500    An error occurred during the material transport
 ERROR 3501    An error occurred when loading the material
 ERROR 3502    An error occurred during the material transport
 ERROR 3503    An error occurred during the material transport
 ERROR 3504    An error occurred during the material transport
 ERROR 3505    An error occurred during the material transport
 ERROR 3506    An error occurred during the material transport
 ERROR 3507    An error occurred when loading the material
 ERROR 3508    An error occurred when loading the material. The end of material has been recognized
 ERROR 3509    An error occurred when loading the material. The end of material has been recognized
 ERROR 350A    An error occurred during the loading process. Material jam has occurred
 ERROR 350B    An error occurred during the loading process. Material jam has occurred
 ERROR 350C    An error occurred during the loading process. There is residual material in the recorder trough. The end of material has been recognized
 ERROR 350D    An error occurred during the unloading process
 ERROR 350F    An error occurred during the unloading process
 ERROR 3510    An error occurred during the unloading process
 ERROR 3511    An error occurred during the unloading process
 ERROR 3512    An error occurred during the unloading process
 ERROR 3515    An error was detected during material feed. Material jam occured
 ERROR 3516    An error was detected during material feed. Material jam in the output unit of the recorder has occured
 ERROR 3600    An internal error occurred when transferring the parameters
 ERROR 3601    An internal error occurred when transferring the parameters
 ERROR 3602    An internal error occurred when transferring the parameters
 ERROR 3700    A problem occurred in the material guide system
 ERROR 3701    A problem occurred in the material guide system
 ERROR 3702    A problem occurred in the material guide system
 ERROR 3703    A problem occurred in the material guide system
 ERROR 3704    A problem occurred in the material guide system
 ERROR 3705    A problem occurred in the material guide system
 ERROR 3706    A problem occurred in the material guide system
 ERROR 4000    Parameter set-up error 
 ERROR 4001    An error occurred during the initialization of the recorder hardware
 ERROR 4002    SlowScan feed error
 ERROR 4003    SlowScan feed error
 ERROR 4004    An error occurred in the SlowScan feed unit
 ERROR 4005    The dust cover and (or) the side panel are not closed
 ERROR 4006    The dust cover and (or) the side panel are not closed
 ERROR 4007    Material jam in the recorder
 ERROR 4008    An error occurred during the material width measurement
 ERROR 6000    An error occurred when accessing the non-volatile memory of the supply cassette
 ERROR 6001    An error occurred when accessing the non-volatile memory of the supply cassette
 ERROR 6002    An internal error occurred when accessing the non-volatile memory of the supply cassette
 ERROR 6003    A non-volatile memory is missing in the recorder
 ERROR 6004    The supply cassette has not been inserted
 ERROR 6005    An internal error occurred when accessing the non-volatile memories
 ERROR 6006    An internal error occurred when accessing the non-volatile memories
 ERROR 6007    An error occurred when accessing the non-volatile memories
 ERROR 6008    An error occurred when accessing the non-volatile memories
 ERROR 6009    An internal error occurred when accessing the non-volatile memories
 ERROR 7000    Internal operating system error
 ERROR 7001    Internal operating system error
 ERROR 7002    Internal operating system error
 ERROR 7003    Internal operating system error
 ERROR 7004    Internal operating system error
 ERROR 7005    Internal operating system error
 ERROR 7006    Internal operating system error
 ERROR 7800    No diskette or the wrong diskette has been inserted
 ERROR 7801    Diskette error: File cannot be opened
 ERROR 7802    Diskette error: File cannot be found
 ERROR 7803    Diskette error: File cannot be read
 ERROR 7804    Diskette error: File cannot be written
 ERROR 7805    Diskette error: File cannot be created
 ERROR 7806    Diskette error: File cannot be deleted
 ERROR 7807    Diskette error: File cannot be renamed
 ERROR 7808    Diskette error: Directory cannot be changed
 ERROR 7809    Diskette error: Directory cannot be created
 ERROR 780A    Diskette error: Diskette is write-protected
 ERROR 780B    The inserted diskette is no UPDATE diskette
 ERROR 780C    The inserted diskette is no recorder system diskette
 ERROR 7C3D    EEPROM Data read error has occured
 ERROR 7C3E    AC-fault greater than 50 milliseconds
 ERROR 7C40    A transmission error on LASERWAY has occured
 ERROR 7C41    The laser power is outside the ready range
 ERROR 7C42    Laser power mode – an adjust timeout has occured
 ERROR 7C43    Laser power supply – an over-temperature error on the passbank has occured
 ERROR 7C44    Laser module – the current limit is reached
 ERROR 7C45    Diode module safety loop test – a bad voltage was detected
 ERROR 7C46    Diode module safety loop check – a logic-fault was detected
 ERROR 7C47    Diode module safety check 2 – a bad voltage was detected
 ERROR 7C48    Diode module safety check 2 – a logic-fault was detected
 ERROR 7C49    Diode module safety check 1 – a bad voltage was detected
 ERROR 7C4A    Diode module safety check 1 – a logic-fault was detected
 ERROR 7C51    Diode module – the EEPROM data is not available
 ERROR 7C52    Diode module – a EEPROM data write failure has occured
 ERROR 7C53    Laser module – a bad microprocessor configuration was detected
 ERROR 7C54    Laser module – a failure of the cooling system was detected
 ERROR 7C55    Laser module – a failure of the heater system was detected
 ERROR 7C58    Diode module – the thermistor is shorted
 ERROR 7C59    Diode module – the thermistor is open
 ERROR 7C5B    Diode module – an over-temperature error has occured ( > 37.5 C)
 ERROR 7C5C    Diode module – an under-temperature error has occured ( < 7.5 C)
 ERROR 7C5D    Laser module – the current limit PASSBANK is reached (2)
 ERROR 7C5E    Laser module – the current limit PASSBANK is reached (1)
 ERROR 7C5F    The laser module safety loop is open
 ERROR 7C62    The diode module relay is closed but should be open
 ERROR 7C63    The diode module relay is open but should be closed
 ERROR 8000    Internal error
 ERROR 8001    Internal error
 ERROR 8002    An error occurred in the recorder hardware
 ERROR 8003    An error occurred in the recorder hardware
 ERROR 8004    An error occurred in the recorder hardware
 ERROR 8005    An error occurred in the recorder hardware
 ERROR 8100    A parameter set-up error occurred in the optics unit
 ERROR 8101    A parameter set-up error occurred in the optics unit
 ERROR 8102    A parameter set-up error occurred in the optics unit
 ERROR 8110    An error occurred in the optics unit of the recorder
 ERROR 8111    An error occurred in the optics unit of the recorder
 ERROR 8112    An error occurred in the optics unit of the recorder
 ERROR 8120    An error occurred in the optics unit of the recorder
 ERROR 8121    A parameter set-up error occurred in the optics unit
 ERROR 8122    A parameter set-up error occurred in the optics unit
 ERROR 8200    An error occurred in the mirror motor unit
 ERROR 8201    A parameter set-up error of the mirror motor unit occurred
 ERROR 8202    An error occurred in the mirror motor unit
 ERROR 8203    An error occurred in the mirror motor unit
 ERROR 8204    An error occurred in the mirror motor unit
 ERROR 8205    An error occurred in the mirror motor unit
 ERROR 8300    The voltage monitoring recognized an error
 ERROR 8301    The voltage monitoring recognized an error
 ERROR 8302    The voltage monitoring recognized an error
 ERROR 8303    The temperature monitoring of the optics unit recognized an error
 ERROR 8304    The temperature monitoring of the optics unit recognized an error
 ERROR 8310    An internal error occurred
 ERROR 83F1    An error occurred when preparing the optics for exposure
 WARNING A600    The recorder is in test operation mode
 WARNING AC00    The selected material is not in the supply cassette
 USER INFO CC00    The image data have not been all processed during the exposure
 USER INFO CC01    The *.RIF initialization file cannot be read from the diskette
 USER INFO CC02    The recorder hardware and software are incompatible
 USER INFO CC03    The recorder received an unacceptable application parameter from the RIP
 USER INFO CC04    The recorder received an unacceptable application parameter from the RIP
 USER INFO CC05    The recorder received an unacceptable application parameter from the RIP
 USER INFO CC06    The recorder received an unacceptable application parameter from the RIP
 USER INFO CC07    The recorder received an unacceptable application parameter from the RIP
 USER INFO CC08    The recorder received an unacceptable application parameter from the RIP
 USER INFO CC09    The recorder received an unacceptable application parameter from the RIP
 USER INFO D000    There is no diskette in the drive
 USER INFO D001    The diskette in the drive is defective or has a wrong format, e.g. DD(720KB)

Mitsubishi Eco 1630

error codes, Polyester CtP

 
 Serial Error    An internal communication error occurred. Re-boot the machine.
 JAM1    The plate is jammed. Cutter not completed cut.
 JAM2    The plate is jammed. Continual discharge.
 JAM3    The plate is jammed. Plate not discharged.
 I/F Error 1    A SCSI communication error occurred. Re-boot the machine.
 ME1    The Cutter does not return to its initial position. Turn on the Power
 Switch again.
 ME2    The Cutter in not located at its initial position. Turn on the Power
 Switch again.
 ME3 Nip Free    The Nip Roller is open. Close the Nip Roller clearance handle.
 ME4    An internal communication error occurred in the machine
 ME5    An internal communication error occurred. Re-boot the machine.
 ME6    The Laser does not light. It may be caused by low Laser.
 ME7    A problem occurred in the Polygon Mirror.
 ME8    A problem occurred in the Processor Heater.
 ME9    A problem occurred in the Heat Roller.
 ME10    A problem occurred when the Punch Unit was activated.
 Disk 01 Error    It may be impossible to use the Disk “01”.
 Disk 02 Error    It may be impossible to use the Disk “02”. 
 Disk Not Found    The Hard Disk drive cannot be found.
 Disk Crash    The Hard Disk drive mounted on this machine cannot be used.
 Please Format HD    The Hard Disk is not formatted.
 HD Partition Error    Format the Hard Disk.
 Punch Un-mounted    The Punch is not mounted.
 Close Front Door    The front door is open. Shut the door.
 Width Not Enough    The width of the plate is insufficient for the exposure width. Replace
 the plate with one as wide as the exposure.
 Image Error    An internal data transmission error occurred. Re-boot machine.
 Plate Set Error    The plate has not been set correctly. Re-set the plate.
 Plate End    The plate ran out. Load new plate.
 Pick Up Plate    Open the front door end remove a strip type plate through the plate
 removal port.
 Waste Tank Check    The waste chemical tank is full.
 Empty EAC    The EAC chemical ran out. Replenish it.
 Empty EST    The EST chemical ran out. Replenish it.
 Tray Check    The overflow try has not been set. Set the tray.

Presstek DPM

error codes, Polyester CtP

Presstek DPM 2508 / Presstek DPM 2340 / Presstek DPM Pro 400

Presstek DPM 2508

Error         Possible Cause                              Recommended Action  
 6012    Media jam in drum or guide box    Clear all media from the drum and guide box area
 6013 or
 6014		    There is no media in the drum.    Insert an input cassette with media. Click the
 menu button on the error handler window to access
 the media database screen. Select the media you
 are loading. Click Load. The job automatically
 starts.
 6015    Take-up Cassette full or contains
 cut media.		    Remove the Take-up Cassette for offline processing
 and replace it with an empty cassette. The job
 automatically starts.
 6016    No Take-up Cassette in the
 machine. Negative film is loaded
 pending job take-up.		    Insert a Take-up Cassette or click Cancel on the
 error handler message window.
 6017    Machine covers open; interlocks
 open.		    Close the machine covers. Respond to the prompt
 to eject the fogged media from the drum. The jobs
 automatically start
 6018    Processor doors open.    Close the processor doors. The jobs automatically
 start.
 6019    Activator Level low.    Wait for the DPM busy indicator to change to
 ready. Replenish activator chemistry. The job
 automatically starts.
 6019    Stabilizer Level low.    Wait for the DPM busy indicator to change to
 ready. Replenish stabilizer chemistry. The job
 automatically starts.
 6020    An internal engine error occurred.    Correct the problem based on the error text
 displayed in the error window. Turn off the DPM and
 turn it back on. Re-enable the RIP output queue.
 6024    Processor temperature is low.    Wait for the processor to warm up, and the job
 automatically starts.
 6026    No guide box in the machine.
 Plate media is loaded pending
 job for processor.		    Install a guide box. The job automatically starts.
 Or cancel the job.
 6027    Media load operation failed.    Retry the load operation. The drum may need to be
 cleared if the load failed because of a jam.
 6028    Media jam in processor.    Clear all media from the processor area.

Presstek DPM 2340

Error         Possible Cause                              Recommended Action  
 6012    Media jam in drum or guide box    Clear all media from the drum and guide box area
 6013 or
 6014		    There is no media in the drum.    Insert an input cassette with media. Click the
 menu button on the error handler window to access
 the media database screen. Select the media you
 are loading. Click Load. The job automatically
 starts.
 6015    Take-up Cassette full or contains
 cut media.		    Remove the Take-up Cassette for offline processing
 and replace it with an empty cassette. The job
 automatically starts.
 6016    No Take-up Cassette in the
 machine. Negative film is loaded
 pending job take-up.		    Insert a Take-up Cassette or click Cancel on the
 error handler message window.
 6017    Machine covers open; interlocks
 open.		    Close the machine covers. Respond to the prompt
 to eject the fogged media from the drum. The jobs
 automatically start
 6018    Processor doors open.    Close the processor doors. The jobs automatically
 start.
 6019    Activator Level low.    Wait for the DPM busy indicator to change to
 ready. Replenish activator chemistry. The job
 automatically starts.
 6019    Stabilizer Level low.    Wait for the DPM busy indicator to change to
 ready. Replenish stabilizer chemistry. The job
 automatically starts.
 6020    An internal engine error occurred.    Correct the problem based on the error text
 displayed in the error window. Turn off the DPM and
 turn it back on. Re-enable the RIP output queue.
 6024    Processor temperature is low.    Wait for the processor to warm up, and the job
 automatically starts.
 6026    No guide box in the machine.
 Plate media is loaded pending
 job for processor.		    Install a guide box. The job automatically starts.
 Or cancel the job.
 6027    Media load operation failed.    Retry the load operation. The drum may need to be
 cleared if the load failed because of a jam.
 6028    Media jam in processor.    Clear all media from the processor area.

Presstek DPM Pro 400

 Serial Error    An internal communication error occurred. Re-boot the machine.
 JAM1    The plate is jammed. Cutter not completed cut.
 JAM2    The plate is jammed. Continual discharge.
 JAM3    The plate is jammed. Plate not discharged.
 I/F Error 1    A SCSI communication error occurred. Re-boot the machine.
 ME1    The Cutter does not return to its initial position. Turn on the Power
 Switch again.
 ME2    The Cutter in not located at its initial position. Turn on the Power
 Switch again.
 ME3 Nip Free    The Nip Roller is open. Close the Nip Roller clearance handle.
 ME4    An internal communication error occurred in the machine
 ME5    An internal communication error occurred. Re-boot the machine.
 ME6    The Laser does not light. It may be caused by low Laser.
 ME7    A problem occurred in the Polygon Mirror.
 ME8    A problem occurred in the Processor Heater.
 ME9    A problem occurred in the Heat Roller.
 ME10    A problem occurred when the Punch Unit was activated.
 Disk 01 Error    It may be impossible to use the Disk “01”.
 Disk 02 Error    It may be impossible to use the Disk “02”. 
 Disk Not Found    The Hard Disk drive cannot be found.
 Disk Crash    The Hard Disk drive mounted on this machine cannot be used.
 Please Format HD    The Hard Disk is not formatted.
 HD Partition Error    Format the Hard Disk.
 Punch Un-mounted    The Punch is not mounted.
 Close Front Door    The front door is open. Shut the door.
 Width Not Enough    The width of the plate is insufficient for the exposure width. Replace
 the plate with one as wide as the exposure.
 Image Error    An internal data transmission error occurred. Re-boot machine.
 Plate Set Error    The plate has not been set correctly. Re-set the plate.
 Plate End    The plate ran out. Load new plate.
 Pick Up Plate    Open the front door end remove a strip type plate through the plate
 removal port.
 Waste Tank Check    The waste chemical tank is full.
 Empty EAC    The EAC chemical ran out. Replenish it.
 Empty EST    The EST chemical ran out. Replenish it.
 Tray Check    The overflow try has not been set. Set the tray.

Esko DPX System Error Codes

error codes, Polyester CtP

Error Description
All errors have both a name and a number that have been divided into different types.
 
 O    Operator has interrupted a sequence, while in Loader Service program
 O1    Error may occur during loading/unloading new material
 J    Error may occur during normal operation
 S    Error indication is not shown in Platesetter Service Monitor
 L    Error indication only shown in Loader Service Program
Error:      Type:       Description:
  10   J      Knife error 
  11   O      Knife error, tighten material abort 
  12   J     Knife error
  13   O      Knife error, remove material abort
  20   O1+J    Park material Time-out (Sensor Feed A = ON)
  21   O1+J    Same as 20, but for B
  30   O1+L    Load material A time-out (Sensor Feed A = OFF)
  31    O    Load material A abort
  32   O1     Load material A time-out (Sensor Drum = OFF)
  33   O1+L    Load material Empty roll A
  34   O1+L    Same as 30, but for B
  35    O    Same as 31, but for B
  36   O1     Same as 32, but for B
  37   O1+L    Same as 33, but for B
  40   O1     Unload material A time-out. (Sensor Feed A = ON)
  41   O1     Same as 40, but for B
  42   O1+L     Unload material Empty roll A
  43    O1+L    Same as 42, but for B
  50    J    Feed material A time-out. (Sensor Drum = OFF)
  51    L+J    Feed material Empty roll A.
  52    O    Feed material A abort
  53    J    Same as 50, but for B.
  54    L+J    Same as 51, but for B.
  55    O    Same as 52, but for B.
  60    O    Cut material Unfeed Abort
  70    O    Unfeed material Abort.
  71    O    Unfeed from Drum. Cut plate in Drum
  72    J    Unfeed material Time-out. (Sensor Jam = ON)
  73    J    Unfeed material Jam. (Sensor Drum = ON)
  80    J    Switch guide. Time-out. (Sensor Switch guide = ON)
  81    J    Switch guide. Time-out. (Sensor Switch guide = OFF)
 82-84    O    Switch guide. Abort
  90    J+O1    Vacuum. Time-out. Incorrect vacuum level
  100    L    Plate in Drum. Switch guide in unfeed position
  101    L    Plate in Drum. Switch guide in feed position
  110    J    Time out, 1 or 2 end stop switches not activated in punch park position
  111    O    Punch. Abort
  112    J    Time out, 1 or 2 end stop switches not activated in punch cut  position
  113    O    Punch. Abort
 

Heidelberg ProSetter

Computer to Plate, error codes

Error:             Description:                                                        More Details:
 0   Recorder is ready for operating    
 1   Internal Error   An error occurred in the program sequence 
 2   Internal Error   An error occurred in the program sequence
 12   Internal Error   Internal communication error
 35   An error occurred in a database.   The specified record is not available.
 36   An error occurred in a database.   The specified error got a different type.
 37   An error occurred in a database.   The length of the value of the specified error is to long for the delivered buffer
 38   An error occurred in a database.   The length of the buffer of the specified record is to short for the delivered value
 40   An error occurred in a database   The insertion of a record into a database is not possible
 41   An error occurred in the file system   A file could not be opened
 42   An error occurred in the file system   A file could not be closed
 43   An error occurred in the file system   A file could not be seeked
 44   An error occurred in the file system   A file could not be written
 45   An error occurred in the file system   A file could not be read
 48   An error occurred while allocating memory   Memory could not be allocated
 49   An error occurred while parsing a source   A syntax error is occurred
 94   Internal system error   Error using operating system function
 95   Internal system error   Error using operating system function
 96   Internal system error   Error using operating system function
 97   Internal system error   Error using operating system function
 98   Internal system error   Error using operating system function
 99   Internal system error   Error in file operation
 100   Internal system error   Error in file operation
 101   Internal system error   Error in file operation
 102   Internal system error   Error in file operation
 103   Internal system error   Error in file operation
 104   Internal system error   Error in file operation
 105   Internal system error   Error in file operation
 106   Internal system error   Error in file operation
 107   Internal system error   Error in file operation
 108   Internal system error   Error in file operation
 109   Internal system error   Error in file operation
 110   Internal system error   Error in file operation
 111   Internal system error   Error in file operation
 112   Internal system error   Error using operating system function
 113   Internal system error   Error using operating system function
 114   Internal system error   Error using operating system function
 115   Internal system error   Error using operating system function
 116   Internal system error   Error using operating system function
 117   Internal system error   Error using operating system function
 118   Internal system error   Error using operating system function
 119   Internal system error   Error using operating system function
 120   Internal system error   Error using operating system function
 121   Internal system error   Error using operating system function
 122   Internal system error   Error using operating system function
 123   Internal system error   Error using operating system function
 124   Internal system error   Error using operating system function
 126   Internal system error   Error in file operation
 128   Internal system error   Error in file operation
 129   Internal system error   Error in filebox
 130   Internal system error   Error in filebox
 133   Communication error   Speedway communication error
 134   Communication error   Speedway communication error
 135   Internal system error   Error using operating system function
 136   Internal system error   Error using operating system function
 146   Internal system error   Internal communication error
 147   Internal system error   Internal communication error
 148   Internal system error   Internal communication error
 149   Internal system error   Internal communication error
 150   Internal system error   Internal communication error
 151   Internal system error   Internal communication error
 152   Internal system error   Internal communication error
 153   Internal system error   Internal communication error
 154   Internal system error   Internal communication error
 155   Internal system error   Error using operating system function
 156   Internal system error   Error using operating system function
 157   Internal system error   Error using operating system function
 158   An error occurred in a database   The erasing of a record out of a database is not possible
 163   Internal system error   Error in file operation
 164   Internal system error   Error in file operation
 170   An internal hardware error occurred   FPGA busy error
 171   An internal hardware error occurred   FPGA detection error
 172   An internal hardware error occurred   FPGA initialization error
 173   An internal hardware error occurred   FPGA busy error
 174   An internal hardware error occurred   FPGA frame data error during configuration
 175   An internal hardware error occurred   FPGA length count error
 220   An error occurred in a database   A file which should be copied does not exist
 221   An error occurred in a database   A file could not be deleted
 222   An error occurred in a database   A file could not be copied
 223   An error occurred in a database   A directory could not be created
 224   An error occurred while parsing a source   A serious syntax error is occurred
 225   An error occurred while parsing a source   A serious syntax error is occurred
 234   Internal error   Operating system error
 235   Internal error   Operating system error
 237   An internal hardware error occurred   Communication error on the SPI Bus
 282   Internal system error   Error in Package
 283   Internal system error   Error in Package
 284   Internal system error   Error in FPGA box
 285   Internal system error   Error in FPGA box
 293   The current machine type is usable for test purposes only   The current machine type is usable for test purposes only
 294   The current machine type is invalid   The current machine type is invalid
 295   The current machine variation is invalid   The current machine variation is invalid
 313   Internal system error   Operating system error
 314   Internal error   Operating system error
 319   An error occurred while parsing a source   A semantics error occurred
 320   An error occurred while parsing a source   Simple semantics error
 321   An error occurred while parsing a source   Serious semantics error
 322   Switch off sequence initiated   Fast switch off sequence initiated
 323   Fast switch off sequence initiated   A second switch off command was received. Only data will be saved before switch 
 324   An error occurred in the parameter database   The parameter configuration file does not exist
 400   Internal error   Undefined error
 401   Internal error   Undefined error
 402   Internal error   Wrong magic number received with the data
 403   Internal error   Buffer size error
 404   Internal error   Checksum error
 405   Internal error   Error after select() function
 406   Internal error   select() timeout
 407   Internal error   Error after ioctl() function
 408   Internal error   Not enough buffer for download
 409   Internal error   Not enough buffer for download
 410   Internal error   Not enough FLASH memory
 411   Internal error   Unknown FLASH vendor
 412   Internal error   Unknown FLASH module
 413   Internal error   Invalid FLASH map
 414   Internal error   FLASH not ready
 415   Internal error   Error clearing the FLASH
 416   Internal error   Error clearing the FLASH
 417   Internal error   Error clearing the FLASH
 418   Internal error   Error clearing a FLASH sector
 419   Internal error   Error clearing a FLASH sector
 420   Internal error   Error checking a FLASH sector
 421   Internal error   Timeout programming the FLASH
 422   Internal error   FLASH not ready
 423   Internal error   Error comparing the FLASH after write operation
 424   Internal error   Error connecting with an interrupt
 425   Internal error   Error activating an interrupt
 426   Internal error   Out of init error memory
 427   Internal error   Error initializing the hardware
 428   Internal error   Error reading from FLASH
 429   Internal error   Error writing to FLASH
 430   Internal error   Error after open() function
 431   Internal error   Error after close() function
 440   Internal system error   Error using operating system function
 441   Internal system error   Error using operating system function
 442   Internal system error   Error using operating system function
 443   Internal system error   Error using operating system function
 3001   The ventilator for the central electronics is defective! Forcing power off of the recorder   Electronics ventilator monitor reports an error. You cannot continue operation. Powering down the recorder
 3002   Wrong Bacher punch configuration   Bacher Configuration parameter (PID 21958) is wrong. The bit map of the Bacher Configuration (PID 21958) must be a subset of the bit map of the Punch Configuration (PID 766)
 3003   The ventilator of the air filter is not working. There will be a loss of recorder quality due to dirty mirrors if this error occurs over a longer period of time   The ventilator of the air filter is not rotating or the phase sequence sensor is defective
 3004   The air filter is used and must be replaced. There will be a loss of recorder quality due to dirty mirrors if this error occurs over a longer period of time   The sensor for the air filter reports that the filter is used
 3005   Max. output level of the optical head is not enough to image in the selected mode   Max. output level of the optical head is not enough to image in the selected mode
 3006   Max. output level of the optical head is not enough to image in the selected mode   Cannot end an action in the recorder because of a preceding error or power-off function
 3007   Punch setting doesn’t match punch configuration   RIP punch action doesn’t match punch configuration
 3008   ATTENTION: Plate lost in device! Do NOT correct error   A plate was probably lost in the device during initialization. Error correction is illegal in this present state
 3009   Internal communication error   Communication with an internal assembly (e.g. Optic) failed
 3010   Internal communication error   Communication with with the Autoloader failed
 3011   Error in the slow scan unit   Could not find resolution for calculation of an imaging ramp
 3012   Network addresses (IP addresses) conflict   The two network addresses of the recorder must not come from the same network
 3014   An error occurred in the mirror motor unit   The time monitor reports timeout during the spin-up phase of the mirror motor
 3015   An error occurred in the mirror motor unit   The time monitor reports timeout during the spin-down phase of the mirror motor
 3016   An error occurred in the air supply unit   The air safety switch is not closed
 3017   An error occurred in the air supply unit   The mirror air cooler temperature is to high
 3018   An error occurred in the air supply unit   Communication error on the I2C-Bus
 3019   Internal communication error   The air pump did not start
 3020   An error occurred in the air supply unit   The focus stepping motor cannot find the zero position
 3021   An error occurred in the optic unit   The focus stepping motor cannot find the zero position
 3022   A parameter set-up error occurred in the optic unit   The focus position set point is not within the permissible range
 3023   An error occurred in the optic unit   The filter stepping motor cannot find the zero position
 3024   An error occurred in the optic unit   The filter stepping motor cannot leave the zero position
 3025   A parameter set-up error occurred in the optic unit   The filter number is not within the permissible range
 3026   A parameter set-up error occurred in the optic unit   The number of the shaping element is not within the permissible range
 3027   An error occurred in the optic unit   The adjust bias current of the laser diode is higher than the maximum current
 3028   An error occurred in the optic unit   The maximum bias current of the laser diode is not sufficient to achieve the required light value
 3029   An error occurred in the optic unit   The adjusted current of the laser diode is higher than the maximum current
 3030   A parameter set-up error occurred in the optic unit   The modulation current of the laser diode set to maximum is not sufficient to achieve the required light value
 3031   An error occurred in the optic unit   The laser diode must be on for the light stabilization
 3032   An error occurred in the optic unit   The light stabilization must be off
 3033   An error occurred in the optic unit   Passed value is to high for this function
 3034   An error occurred in the optic unit   Passed value is to low for this function
 3050   On board device error   Unable to set mirror power supply (36 V)
 3051   An error occurred in the slow scan unit   The stepper board signals a short circuit, the safety loop is open or power supply (36V) failed
 3052   An error occurred in the slow scan unit   The stepper board signals high temperature
 3053   An error occurred in the slow scan unit   The stepper board signals not ready
 3054   An error occurred in the slow scan unit   The carrier reaches the left limit
 3055   An error occurred in the slow scan unit   The carrier reaches the right limit
 3056   An error occurred in the slow scan unit   The carrier is moving when it is not allowed
 3057   An error occurred in the slow scan unit   The safety loop is not closed
 3058   An error occurred in the slow scan unit   An interrupt has occurred when not expected. Interrupt: Stop
 3059   An error occurred in the slow scan unit   An interrupt has occurred when not expected. Interrupt: Signal of light barrier has changed
 3060   An error occurred in the slow scan unit   An interrupt has occurred when not expected. Interrupt: Destination reached
 3061   An error occurred in the slow scan unit   A SlowScan timeout is occurred during finding a position or moving into the light barrier
 3062   An error occurred in the slow scan unit   A valid ramp could not be found
 3063   An error occurred in the slow scan unit   A ramp which fits into a specified distance could not be found
 3064   A parameter error occurred   The value of a parameter is not valid
 3078   An internal software error occurred   An attempt to read an uninitialized ADC device.
 3088   An error occurred while material handling   Timeout at build vacuum
 3089   An error occurred while material handling   Timeout at vacuum off
 3138   An error occurred at punch init   Punch not connected or not configured
 3159   An error occurred in the slow scan unit   The safety loop is not closed
 3160   An error occurred in the slow scan unit   The carrier reaches the left limit
 3161   An error occurred in the slow scan unit   The carrier reaches the right limit
 3162   An error occurred in the slow scan unit   The stepper board signals not ready
 3165   An error occurred while setting the light intensity   The BaseIntensity value for the selected resolution of the current job is lower than the adjustable light
 3168   An error occurred in the slow scan unit   The feed ramp could not be written
 3169   An error occurred in the slow scan unit   Error while calculating feed ramp data
 3198   Not calibrated resolution selected   The selected resolution is not calibrated. The BaseIntensity parameter for the selected resolution is zero
 3199   An communication error to the optic head occurred   The communication to the optic head is broken
 3200   An communication error to the optic head occurred   The communication to the optic head is faulty
 3201   An error occurred in the optichead unit   The number of gate impulses generated by the Image-Control is out of range
 3202   An error occurred in the optichead unit   The temperature of the laser diode did not change after switching on the temperature regulation
 3203   An error occurred in the optichead unit   The temperature of the laser diode is over the maximum allowed temperature
 3204   An error occurred in the optichead unit   A parameter transmitted to the optichead is out of range
 3205   An error occurred in the optichead unit   A parameter transmitted to the optichead is out of range
 3206   An error occurred in the optichead unit   An error without a defined event has occurred
 3207   An error occurred in the optichead unit   The light value on the laser diode with the bias current alone is higher than the value in the application data. This may be due to an error in the primesetter or a not initialized material data set or an defective optichead
 3208   An error occurred in the optichead unit   The error occurs if you switch on the temperature regulation on the optichead without a regulation device
 3209   An error occurred in the optichead unit   The mirror phased out during transmission. The mirror is not locked
 3211   The mirror phased out during transmission. The mirror is not locked   The detect vacuum is much too low
 3212   An error occurred while selecting the focus value   The RIP transmitted resolution is not a element of the recorder resolution table
 3213   An error occurred while selecting the focus value   The calculation of the spotshape value failed
 3214   An error occurred in the optic unit   The calculation of the filter value failed
 3215   An error occurred in the optic unit   The calculation of the physical focus value failed
 3216   An error occurred in the optic unit   The calculation of the physical focus value failed
 3217   The safety loop was at least briefly interrupted    
 3226   An error occurred while setting the light intensity   The BaseIntensity value for the selected resolution of the current job is lower than the adjustable light
 3227   An error occurred while setting the light intensity   The BaseIntensity value for the selected resolution of the current job is higher than the adjustable light
 3228   An error occurred in the optichead unit   The light value on the laser diode with the modulation current alone is to high . This may be due to an error in the primesetter or an defective optichead
 3229   An error occurred in the air supply unit   The high-water sensor is still active, after water blow-off
 3230   An error occurred in the air supply unit   The high-water sensor is still active, after water blow-off
 3238   Plate on table missing for load   Possibly plate detector (on plate table) defect
 3239   An error occurred at punch action   Timeout at punch action (10s) at arrive ls
 3240   An error occurred at material transport   Timeout at drive plate slider to Down-Wait Position (prepare to load)
 3241   An error occurred at material transport   Timeout at drive plate slider to Down-Free position (unload plate)
 3242   An error occurred at material transport   Timeout at drive plate slider to Up-Unload Position (unload plate or init)
 3243   An error occurred at material transport   Timeout at center plate on table
 3244   Plate on the table is not valid. Measured plate width is different to requested plate   Plate on the table is not valid. Measured plate width is different to requested plate
 3245   Inserted plate is not valid. Measured plate length is different to requested plate   Inserted plate is not valid. Measured plate length is different to requested plate
 3246   Unexpected plate on table detected. Exposed plate can not be ejected   Unexpected plate on table detected. Exposed plate can not be ejected
 3247   An error occurred at material transport   A timeout is occurred during moving the lift into a position. No interrupt occurred
 3248   There is no plate at the grip. Loading material isn’t possible   The plate sensor at the grip signals no-plate
 3249   An internal hardware error occurred   The lift stepping motor cannot find it’s zero position
 3250   An internal hardware error occurred. One or more fans at the back-wall don’t work   One or more of the guide fans at the back-wall don’t work
 3251   An internal hardware error occurred. One or more fans at the back-wall don’t work   One or more of the guide fans at the back-wall don’t work
 3252   An internal hardware error occurred. One or more fans at the back-wall don’t work   One or more of the guide fans at the back-wall don’t work
 3253   An internal hardware error occurred. One or more fans at the back-wall don’t work   One or more of the guide fans at the back-wall don’t work
 3254   The safety loop is open   The safety loop is open
 3255   An internal hardware error occurred   An internal hardware error occurred
 3256   An internal hardware error occurred   An internal hardware error occurred
 3258   Plate position in lift is not valid for unloading   Inserted plate is not valid. Measured plate length is different to requested plate
 3259   An error occurred at material transport   An error occurred at material transport
 3260   An error occurred at material transport   Moving the flaps failed. They didn’t reach their in-or-out target position
 3261   An error occurred at material transport   Moving the flaps failed. They didn’t reach their in-or-out target position
 3262   An error occurred at material transport   Lift didn’t reach it’s set position. Maybe stopped by a sporadic interrupt
 3263   An error occurred at material transport   Moving the lift isn’t possible because the flaps stays in the path
 3264   An error occurred at material transport   Moving the lift isn’t possible because the grip unit is in horizontal position
 3265   An error occurred at material transport   There are no valid parameter available
 3266   An error occurred at material transport   Lift lost it’s position. Lower reference light-barrier shows a position error bigger than 1.2mm 
 3267   Material Length isn’t possible to load   It isn’t possible to move the lift into the calculated load position for this material length
 3269   An error occurred at material transport   This operation isn’t possible at this time because the system wasn’t initialized correctly 
 3270   The set lift position is out of range   It isn’t possible to move the lift into the calculated load position for this material length 
 3271   An error occurred at material transport   There are no valid parameter available 
 3272   An error occurred at material transport   Initializing of the lift not possible – maybe the grip is still under the hooks in the indrum 
 3274   An error occurred in the lift and grip unit   The stepper board signals not ready
 3275   An error occurred in the lift and grip unit   The lift ramp could not be written
 3276   An error occurred in the lift and grip unit   Error while calculating lift ramp data
 3277   An error occurred in the lift and grip unit   Moving the lift isn’t possible because the flaps stays in the path
 3278   An error occurred in the lift and grip unit   FPGA and Parameter Grip Mode do not match
 3279   part of the covering isn’t closed correctly or the emergency switch is activated    
 3280   Exposed plate is keeping in recorder   Exposed plate is keeping in recorder
 3281   The service switch bypasses the safety loop    
 3286   Unexpected plate on table detected. Init recorder or error correction not possible   Unexpected plate on table detected. Init recorder or error correction not possible
 3287   An error occurred in the lift and grip unit   The lift stepping motor cannot find it’s zero position
 3288   An internal hardware error occurred. One or more fans at the plate-table don’t work   One or more of the guide fans at the plate-table don’t work
 3289   An internal hardware error occurred. One or more fans at the plate-table don’t work   One or more of the guide fans at the plate-table don’t work
 3296   Voltage failure    The negative analog 5 V failed 
 3297   Voltage failure    The negative analog 5 V failed 
 3298   Voltage failure    The negative analog 5 V failed 
 3299   Voltage failure    The positive 36 V failed 
 3300   Voltage failure    The positive 15 V failed
 3301   Voltage failure    The positive 42 V failed
 3302   Voltage failure    The positive 7.5 V failed 
 3303   Voltage failure    The positive 7.5 V failed 
 3304   Voltage failure    The positive analog 24 V failed 
 3305   Voltage failure    The positive 3.3 V failed 
 3306   Voltage failure    The positive 2.5 V failed 
 3307   The positive 2.5 V failed    Safety loop check failed. Check the Logfile for further information
 3309   An error occurred in the material base   The requested material does not exist
 3310   An error occurred at material transport   The plate center unit does not left the light barrier
 3311   An error occurred at material transport   An unexpected motor stop from stepper counter at plate centering
 3312   An error occurred in the air supply unit   The air pressure did not reach the required minimum
 3315   The aging of the laser diode has accelerated   Too few exposure time has elapsed since the last automatic increase of the bias current setvalue. Nevertheless the bias current setvalue will be increased
 3316   The end of lifetime of the laser diode is approaching   The nominal maximum limit of the total current of the laser diode has been reached
 3317   An error occurred in the air supply unit   The mirror air pressure is above stop-limit
 3318   An error occurred in the air supply unit   The mirror air pressure is above stop-limit
 3325   An error occurred in the material base. The preferred shaft has not been specified   The preferred shaft is used in case a material shall be loaded which gets no link from any shaft
 3326   An error occurred in the material base   The name of the material that is send with the command request material is invalid
 3327   Remove Plate from table. Plate is exposed   Remove Plate from table
 3328   Remove Plate from table. Plate is unexposed   Remove plate from manual tray
 3329   OLP program change necessary   OLP program change necessary
 3913   Autoloader error state detected   Autoloader error state detected
 3914   Internal software or parameter error   Syntax error in debug configuration
 3915   The Emergency Switch is activated    
 3916   The boot sequence failed. Please reboot the system   The boot sequence failed. Please reboot the system
 4001   Internal software or parameter error   Syntax error in debug configuration
 4002   Execution error – A general STOP occurred   A general BREAK occurred
 4003   Internal error – sensor not recognized   A sensor in the device does not respond
 4004   Internal error – setting a sensor failed   Writing to a sensor failed
 4005   Internal error – actuator not recognized   An actuator in the device does not respond
 4006   An actuator in the device does not respond   Writing to an actuator failed
 4007   Error checking the Cassette/Waste safety loop   There is a problem with the safety loop of the Cassette / Waste section. Checking it failed
 4008   Invalid Autoloader machine type set    
 4009   Any part of the covering isn’t closed correctly    
 4010   The safety loop was at least briefly interrupted    
 4011   The service switch bypasses the safety loop    
 4012   Internal system error   Error using operating system function
 4013   Error checking the cover safety loop   There is a problem with the safety loop of the cover section. Checking it failed
 4014   Runtime error   Internal software error
 4015   The Emergency Switch is activated    
 4016   The boot sequence failed. Please reboot the system   The boot sequence failed. Please reboot the system
 4100   Error separating a plate    
 4101   Error initializing the shutter   Unable to access the shutter init sensor
 4102   Error initializing the shutter   Unable to quit the shutter init sensor
 4103   Error moving the shutter   Unable to move the shutter into waste position
 4104   Error moving the shutter   The shutter failed to get to the material transfer position
 4105   Error polling a load table plate sensor   Load table plate sensor on the suction cart not found
 4106   Error separating   Plate lost while separating or during transport to the entry of the load table plate. The plate did not arrive at the relevant sensor
 4107   Error placing the plate on the load table plate   Plate lost during transport to the load table plate, the table plate sensor on the suction cart fails to detect the plate at the end of the transfer process
 4108   Error moving the shutter   Separator exit sensor not left when transporting the plate to the load table plate
 4109   Paper sheet lost when separating   When depositing the paper sheet, the vacuum shows that the sheet was lost during transfer into the waste container
 4110   Error initializing the stripper unit   Stripper unit did not arrive at the init position during initialization
 4111   Error initializing the stripper unit   Unable to quit the init sensor of the stripper unit
 4112   Error moving the stripper unit into working position   Unable to quit the parking sensor of the stripper unit
 4113   Error moving the stripper unit   Unable to get to the parking sensor of the stripper unit
 4115   Moving the stripper unit into the parking position caused an error several times   Moving the stripper unit into the parking position caused an error several times
 4116   A sensor was not reached while the stripper unit was moving to its park position   The light barrier of the park sensor was not detected while the stripper unit was moving to its park position
 4117   A sensor was not reached during initialization of the stripper unit   The light barrier of the park sensor was not detected during initialization of the stripper unit
 4118   A sensor was not reached during normalization of the shutter   A sensor was not reached during normalization of the shutter
 4119   A sensor was not reached during initialization of the shutter   The zero light barrier was not detected during initialization of the shutter
 4120   Error initializing the cassette shutter   Cassette shutter motor did not arrive at the init position during initialization
 4121   Error initializing the cassette shutter   Unable to quit the init position when initializing the cassette shutter motor
 4122   Error while preparing cassette shade drive for taking a new cassette   Sensor could not detect the requested phase 1 during the specified number of attempts during initialization of the cassette shade drive
 4123   Error while preparing cassette shade drive for taking a new cassette   Sensor could not detect the requested phase 2 during the specified number of attempts during initialization of the cassette shade drive
 4124   A sensor was not reached during initialization of the cassette shade drive   The light barrier of the close sensor was not detected during initialization of the cassette shade drive
 4130   Error moving the suck bar   The suck bar did not arrive in its new position during the expected time
 4133   Error lowering the suck bar   The suck bar is not at its bottom position as expected
 4134   Error moving the suck bar   The suck bar is not at the middle position as expected
 4135   Error lifting the suck bar   The suck bar is not at the top position as expected
 4136   Error moving the suck bar   The suck bar does not move
 4137   Error setting the suck bar parameters   A command to the suck bar returned an invalid command
 4138   While separating, double sheet error Paper under plate occurred several times without a plate being present   While separating, double sheet error Paper under plate occurred several times without a plate being present
 4139   A piece of paper, located on the Jalousie, couldn’t fix by the suck bar   A piece of Paper couldn’t move from the suck bar to the Jalousie suction bar
 4140   Error setting the separator ejector parameters   Invalid command encountered when enabling the ejector’s blowing function
 4141   Error setting the separator ejector parameters   Invalid command encountered when enabling the ejector’s suction function
 4142   Error setting the separator ejector parameters   Invalid command encountered when actuating the compressed air supply of the ejector’s suck bar
 4143   Error setting the separator ejector parameters   Invalid command encountered when actuating the compressed air supply of the ejector’s suction bar
 4144   Vacuum error signaled by vacuum sensor. Unable to suck and hold the material or material lost   The vacuum sensor of the separator detected an insufficient vacuum
 4152   Error setting the double sheet sensor parameters   Invalid command encountered when selecting the double sheet sensor
 4153   No or not enough compressed air   Poll of compressed air status result: no compressed air
 4154   Error separating. A double sheet detected cannot be separated because the suction bar is carrying material already    
 4155   A double sheet detected on the jalousie. The material could not be separated   The double sheet must be removed manually by hand
 4156   A double sheet was detected on the Jalousie. The material couldn’t be split   The double sheet couldn’t fix by the suck bar – it must be removed by hand
 4157   A double sheet was detected on the Jalousie. The material couldn’t be split   The double sheet couldn’t fix by the suck bar – it must be removed by hand
 4161   Tray empty. No material on the active tray   No material found when reading the tray fill level
 4162   A detected double sheet on the Jalousie couldn’t move to the Load Table   A double sheet wasn’t detected from the exit-sensor of the separator
 4163   A double sheet was detected on the Jalousie. The material couldn’t be split within several tries   The double sheet couldn’t be split within several tries – it must be removed by hand
 4164   While checking the material at the suction bar, an error with the vacuum occurred    
 4165   While sucking the paper with the suck bar, a vacuum error occurred   There was no vacuum at the suction bar
 4166   The paper could not be removed, because the cassette was not open    
 4167   While loading and locking the cassette an error occured inside the SCL    
 4171   Clamp jaw unit error   Unable to close the clamp jaw
 4172   Clamp jaw unit error   Unable to open the clamp jaw unit – the unit will not release the plate
 4173   Error closing the clamp jaw unit   Unable to close the clamp jaw unit during the expected time
 4174   Error closing the clamp jaw unit   Unable to open the clamp jaw unit during the expected time
 4181   No material found in the cassette   No material was detected during check of cassette level
 4182   Almost no material in the cassette   A check of the cassette level detected only a few plates still in the cassette. The number has fallen below the set alert level
 4183   The waste container is full   A check of the waste container level detected that the container is full
 4184   The waste container is almost full   A check of the waste container level detected that the set alert level was exceeded
 4190   Error setting the waste container parameters   Invalid command encountered when opening / closing the waste container
 4191   Unable to open the waste container   The waste container could not be opened because it was impossible to move the shutter into the specified position
 4192   Waste container open   Could not open the cassette because the waste container was not closed
 4193   Vacuum error at the suction bar. Could not suck the material to the bar or the material was lost   Vacuum sensor detected that the vacuum was too low when the suction bar of the separator was used
 4194   Vacuum error after raising the suction bar. Could not suck the material to the bar or the material was lost   Vacuum sensor detected that the vacuum was too low after raising the suction bar
 4195   Configuration error – unknown machine type   Invalid machine type set
 4196   Error separating   Plate lost while separating or during transport to the entry of the load table plate. The plate did not arrive at the relevant sensor
 4197   Error separating   Material lost when lifting it out of the tray
 4198   An error occurred during initialization or error handling. Material was found on the shutter   Material was found on the shutter during initialization or error handling. The material is to be removed by the operator
 4201   Unable to determine the position of the load table plate   Both load table plate position sensors output the same signal
 4202   Error moving the load table   Timeout encountered when swivelling/moving the load table
 4203   The load table fans are not working    
 4204   Error moving the plate holder   Timeout encountered when lifting/lowering the plate holder
 4205   Error initializing the plate holder   The plate holder did not move away from its init sensor
 4206   Error initializing the plate drive motor   The plate holder did not move up to its init sensor
 4207   Error initializing the plate drive motor   Initialization of the plate drive motor failed. Absolute positioning of the plate holder is not possible
 4208   No plate on the load table   The procedure requires a plate but none has been detected
 4209   Error initializing the center unit   The center unit did not move away from its init sensor
 4210   Error initializing the center unit   The center unit did not move up to its init sensor
 4211   Material transport error   Error transporting the plate from the load table to the conveyor
 4212   Plate not in the gripper   The plate did not move up to the grip sensor
 4213   The plate did not move up to the grip sensor   Wrong width of plate. See the log file for further details
 4214   Load table process error   A signal expected from the load table holder sensor not received
 4215   Error initializing the load table   The states of the load table sensors have been checked. The result is an impossible combination
 4226   Double sheet detected on load table during material transport to recorder   Please remove the material manually by hand
 4227   The load table can not be moved, because material was detected between separator and load table   Material was detected in light barrier of the separator. The material is to be removed by the operator before moving the load table
 4301   Error moving the conveyor   Timeout lifting/lowering the conveyor table
 4302   Error initializing the conveyor roller motor   Initialization of the conveyor roller motor failed
 4303   Error transporting the plate from the conveyor to the load table   Plate transport from the conveyor to the load table is not possible. The plate has left the range of the entry sensor already
 4304   Error centering the plate on the conveyor   Unable to fully load the plate onto the conveyor. The conveyor entry sensor is not free
 4305   No plate on the conveyor   The procedure requires a plate but none has been detected
 4306   Configuration error – no valid assembly position of the online processor   Assembly position of the online processor wrong or not specified
 4307   Error centering the plate on the conveyor   Conveyor center sensor not enabled
 4308   Error initializing the conveyor slider   The conveyor slider did not move away from its init sensor
 4309   Error initializing the conveyor slider   The conveyor slider did not move up to its init sensor
 4310   Error initializing the conveyor slider   Initialization of the conveyor slider motor failed
 4311   Error unloading the plate   Signal expected from the conveyor entry sensor not received
 4312   Conveyor process error   Signal expected from the conveyor slider init sensor not received
 4313   Error actuating the online processor   No ON signal of the online processor
 4314   Error actuating the online processor   No connect signal of the online processor
 4315   Configuration error – wrong online processor interface set   The set online processor interface is unknown
 4316   Error unloading the plate   Error centering the plate on the conveyor. The computed correction exceeds the maximum
 4317   Error unloading the plate   Signal expected from the conveyor exit sensor not received
 4318   Error unloading the plate   Signal expected from the conveyor center sensor not received
 4319   Error initializing the conveyor   The states of the conveyor sensors have been checked. The result is an impossible combination
 4320   Error centering the plate on the conveyor   Unable to readjust the plate onto the conveyor. The plate is expected on the entry sensor but isn’t there
 4401   An error occurred while swinging out the cassette drive   One of the two cassette drives did not reach its swing-out position in the allotted time
 4402   An error occurred while swinging out the cassette drive   One of the two cassette drives did not leave its swing-out position in the allotted time
 4403   An error occurred during the cassette drive setup   An invalid command for the cassette drive was detected
 4404   An error occurred while evaluating the current cassette position   The sensors for the horizontal cassette position returned an invalid position
 4405   No cassette was detected at the MCL exit when conveying a cassette from the SCL to the MCL   The exit sensor of the MCL did not detect a cassette
 4406   No cassette was detected at the MCL entry when loading a cassette   The cassette drive sensor (perhaps the entry sensor as well) did not detect a cassette
 4407   No fully loaded cassette was detected while unloading a cassette from the MCL    
 4408   A cassette could not be positioned correctly while loading it from the SCL   The specified number of attempts to position the cassette was exceeded
 4409   A cassette could not be positioned correctly while loading it from the trolley   The specified number of attempts to position the cassette was exceeded
 4410   Error closing the inlet door   The inlet door did not reach the position in the allotted time
 4411   Error opening the inlet door   The inlet door did not reach the position in the allotted time
 4412   An error occurred while evaluating the current inlet door position   The sensors for the inlet door position returned an invalid position
 4413   An error occurred during the setup of the inlet door drive   An invalid command for the inlet door drive was detected
 4414   The inlet door was not open before a cassette was unloaded to the trolley    
 4415   The inlet door was not closed before the elevator moved    
 4420   Error initializing the elevator   The elevator init sensor was not reached
 4421   Error initializing the elevator   The elevator init sensor was not left
 4422   An error occurred while evaluating the current elevator position   The sensors for the vertical cassette position detected an invalid position
 4423   Failed to find cause of aborted movement after elevator or cassette drive finished moving   The cause was an undefined event
 4424   The elevator or cassette drive did not finish moving by reaching a sensor    
 4425   An error occurred while moving the elevator   The error bit of the elevator motor is active
 4426   A safety error occurred before the elevator moved   One of the two cassette drives is not swung out
 4427   A safety error occurred before the elevator moved   The cassette in the SCL was not locked
 4428   An error occurred while evaluating the current elevator position   The sensors for the vertical cassette position returned an invalid position
 4429   An error occurred during the elevator setup   An invalid command for the elevator was detected
 4440   No fully loaded cassette was detected before unloading a cassette from the MCL to the SCL or the trolley    
 4441   No fully loaded cassette was detected after loading a cassette from the SCL or the trolley  to the MCL    
 4442   No cassette was detected at the MCL entry sensor before loading a cassette from the SCL to the MCL    
 4443   No cassette was detected at the MCL exit sensor after unloading a cassette from the MCL to the SCL    
 4444   No cassette was detected at the MCL entry sensor before loading a cassette from the trolley to the MCL    
 4445   No cassette was detected at the MCL entry sensor after unloading a cassette from the  MCL to the trolley    
 4446   A cassette was detected to be not fully loaded to its position before the elevator moved    
 4447   The cassette is not in valid position    
 4448   No trolley was found in front of the MCL before unloading a cassette from the MCL    
 4449   A cassette was detected in the SCL before unloading a cassette from the MCL to the SCL    
 4450   The elevator could not be moved or movement had to be stopped too soon because the cassette drive was no longer swung out    
 4451   An error occurred, at least one safety relay of the MCL is open    
 4460   Movement of elevator started, duration approximately 90 sec    
 4461   Movement of elevator started, duration approximately 60 sec    
 4462   Movement of elevator started, duration approximately 30 sec    
 4500   No tray with the requested material   Further processing will be paused until a tray with the requested material has been put in
 4501   The waste container is open   Further processing will be paused until the waste container has been closed
 4502   The load table is not free. The system may be waiting for a plate to be moved on into the online processor   Further processing will be paused until the load table is free again
 4503   The conveyor is not free. The system may be waiting for a plate to be moved on into the online processor   Further processing will be paused until the conveyor is free again
 4504   The trolley is not in loading/unloading position   Further processing will be paused until the trolley is in the correct position
 4505   Online processor not ready – no connect signal   Further processing will be paused until a connect signal has been received from the online processor
 4506   The online processor is off   Further processing will be paused until the online processor is on and has sent a ready signal
 4507   The online processor is busy   Further processing will be paused until the state of the online processor has changed from Busy to Not Busy
 4508   The paper container is full   Further processing will be paused until the paper container has been opened and emptied
 4509   Tray empty   Further processing will be paused until the tray has been removed, filled with material and put back in
 4510   No or not enough compressed air   Further processing will be paused until the pressure level has reached the required value
 4511   Remove the cassette   Further processing will be paused until the cassette has been removed
 4512   Insert required plate to bypass   Insert required plate to bypass
 4513   Remove plate from bypass. Plate width is not as requested   Remove plate from bypass
 4520   Shaft data inconsistency detected. Rescan initiated (approx. 120 sec.)    
 4530   Error executing comand   The DAL command is not implemented
 4531   Error executing command   The DAL command was rejected
 4532   Error loading/unloading a cassette   Loading/unloading the cassette to the specified tray was impossible as the tray already contained a cassette
 4533   Error loading/unloading a cassette   The specified tray number is out of ra
 4534   Error loading/unloading a cassette   The specified tray type is incorrect
 4535   Error loading/unloading a cassette   The state of the specified tray is incorrect
 4536   Initialization failed   The initialization loop exceeded the maximum
 4537   Error Correction failed   The error correction loop exceeded the maximum
 4538   Shut down failed   The shutdown loop exceeded the maximum
 4988   An error was detected in the horizontal drive of the MCL   The elevator’s motor control detected an error and switched itself off
 4989   Error initializing a motor   Unable to quit the home sensor
 4990   Error initializing a motor   Expected home sensor not found at the target position
 4991   Error controlling a motor   Expected sensor not found at the target position
 4992   Error controlling a motor   Invalid parameter found when computing the data for stepper motor actuation
 4993   Error controlling a motor   No actuation data found when starting the stepper motor
 4994   Error controlling a motor   Insufficiently larger memory range found when computing the data for stepper motor actuation
 4995   Error controlling a motor   Absolute motor positioning not possible, the motor is to be initialized first
 4996   Error controlling a motor   Timeout actuating the stepper motor
 4997   Error controlling a motor   Invalid minimum frequency for actuating the stepper motor
 4998   Error controlling a motor   Invalid parameter found when computing the data for stepper motor actuation
 4999   Error controlling a motor   Error computing the data for actuating the stepper motor